Parts and their functions, Front panel, Push lock – Panasonic HD1700pe User Manual
Page 12: Push-inter, Unity, Cf f1 f5 f1, F9 1
12
N PREROLL button
This button is used to locate where a transmission
or manual editing starts on the tape.
When it is pressed, the tape travels to the preroll
point and it stops there.
When the cue time has been registered on the
HOME, PF1 or PF2 screen:
The tape is prerolled from the registered cue time
using the preroll time which was set using
.
(PREROL) on the
When the search mode is established on the
CUE screen:
The tape is prerolled from the selected cue point
using the preroll time which was set using
(CU-ROL) on the
The preroll operation is not performed when the
selected cue point has not been registered or
when the cue point registration mode is
established.
In all other situations:
The tape is prerolled from the registered IN point
(or the current tape position when the IN point has
not been registered) using the preroll time which
was set using
[
(PREROL) on the SHIFT> menu. When the PREROLL button is pressed together key among the number keys. O IN (A IN), SET and OUT (A OUT) buttons When the IN (A IN) or OUT (A OUT) button is pressed button is pressed while holding down the IN (A IN) or OUT (A OUT) button, the registration of C F F1 F5 F1 Front panel J Audio channel selector button Use this button to select whether the audio controls K Number keys Use these keys to input the numerical values of the to while the key is held down, alphabet letters from A to F which are used for the user’s bit or letters from A to L PREVIEW/REVIEW button PREVIEW: When the button is pressed after an edit point has been registered, the tape travels and the REVIEW: When the button is pressed after a section has been edited, the just edited section is M AUTO EDIT button When this button is pressed after the edit points F 9 1 Parts and Their Functions POWER OFF ON HEADPHONES PUSH FULL CH CONDITION MONITOR FULL/FINE REMOTE L R 9P 50P RS-232C CH 1 2 3 4 5 6 7 8 CUE XL/L/M-cassette Do not insert S-cassette without adapter EJECT AUDIO CH SELECT SHIFT ABC DEF GHI JKL MNO PQRS PREVIEW/ REVIEW PRE- A IN A OUT HOME RF1 ASSEM ADJUST SHTL REV FWD VAR JOG STAND BY RECORDER INPUT CHECK PLAYER SERVO EDIT PLAY REC REW STOP FF REC INHIBIT PUSH-INTER INSERT RF2 VIDEO UNITY TC CUE AUDIO UNITY DIAG MENU TRIM SET IN OUT AUTO EDIT 7 8 9 4 5 6 BS TUV WXYZ 1 2 3 ENT 0 C T F F1 F2 F3 F4 F5 F6 CH 1 CH 5 CH 2 CH 6 CH 3 CH 7 CH 4 CH 8 FULL REC P8 REC P8 REC P8 REC P8 N L J M K O
If the PREROLL button is pressed when the IN
point has not been registered, the current tape
position is automatically registered as the IN point
(but only when ENA has been selected as the
setup menu item No.305 (AUTO ENTRY) setting).
with the IN (A IN) or OUT (A OUT) button, the tape
can be cued up to the registered point concerned.
To cue up the tape for the cue time registered on
the HOME, PF1 or PF2 screen, press the
PREROLL button while holding down the
together with the SET button, the IN (A IN) or OUT (A
OUT) point is registered.The A IN and A OUT buttons
are used to register audio IN and OUT points that
differ from the corresponding video points during
audio split editing.
When an IN (A IN) or OUT (A OUT) point has been
registered, the lamp of the IN (A IN) or OUT (A OUT)
button which has registered that point lights. When
these buttons are pressed after points have been
registered, the IN (A IN) or OUT (A OUT) point value
appears on the counter display.
When the
the IN (A IN) or OUT (A OUT) point is cleared.
for channels CH1 to CH4 or for channels CH5 to
CH8 are to be controlled.
Each time it is pressed, the channel display LED
above the audio control is selected.
CUE points, edit points, etc.
By pressing a number keys from
Z which are used to compose filenames can be
input.
Since a multiple number of letters are allocated to
each number key, keep tapping the number key
until the desired letter is selected. To change the
input position, use the ADJUST dial, and then
proceed with the input.
editing can be previewed without actually
performing the editing.
If the button is pressed when the IN point has not
been registered, the point where it was pressed is
registered as the IN point, and preview is
executed using this IN point.
played back, and it can be reviewed on the
recorder’s monitor.
have been registered, automatic editing is initiated.
If the button is pressed when the IN point has not
been registered, automatic editing is initiated with
the point where the button was pressed serving as
the IN point.
LOCK
ROLL