FujiFilm FinePix S3Pro - Manual (Page 56)

110 111
Settings
5
CUSTOM SETTING (CSM)
The custom settings allow to modify camera functions such as how information is displayed in the
viewfinder and which functions are assigned to which buttons.
Cancelling custom settings
1 Set the Exposure mode dial to “CSM”.
2 1 Turn the Main-command dial to select an option.
2 Turn the Sub-command dial to change the
setting.
3 “E” appears on the top display panel.
3 When you have finished the settings, set the exposure mode dial to a setting other than “CSM”.
● ! The custom settings are retained when the camera is turned off.
1 Set the Exposure mode dial to “CSM”.
2 Hold down the “c” and “b” buttons together
for at least 2 seconds (green markings are
positioned alongside).
The top display panel flashes briefly and the
settings are reset.
h All the custom settings are reset to their default
values.
h The ISO sensitivity is reset to 200.
0 2 0 1
0 3
0 2
0 1
0 2
■ Custom settings list
Setting No. Display Details
0: METERED VALUE
➡ UNDER ➡ OVER
(default)
1: UNDER ➡
METERED VALUE
➡ OVER
BRACKETING ORDER 1
2
3
4
5
6
7
8
9
10
Allows you to change the compensation sequence
when auto exposure bracketing is used.
0: OFF (default)
1: ON ON-DEMAND GRID
LINES DISPLAY If you display the On-Demand Grid Lines, you can use
the intersections of the horizontal and vertical lines to
position your main subject in the shot or align one of the
horizontal lines with the horizon. This allows you to
compose the desired shot while monitoring the subject's
size and the balance.
0: AUTO (default)
1: OFF
2: ON ILLUMINATION FOR
FOCUS AREA Specifies the illumination used for the focus area in the
viewfinder.
0: NORMAL (default)
1: ENABLES
ROTATION
FOCUS AREA
SELECTION Selecting cyclic focus area selection allows you to
select the opposite focus area without changing which
part of the 4-direction button you have to press.
0: DISABLED (default)
1: ACTIVATED AE-LOCK Set this parameter to “1” to apply the AE lock when the
shutter button is pressed half way.
0: DISABLED (default)
1: ACTIVATED LONG EXP. (BULB) AT
MANUAL MODE Select “1” to take bulb shots in the “M” exposure mode.
0: ENABLED (default)
1: DISABLED CLOSEST-SUBJECT-
PRIORITY DYNAMIC AF
AT AF-S MODE If you select “1”, Closest-subject Priority Dynamic AF is
not used in AF-S mode.
0: DISABLED (default)
1: ENABLED CLOSEST-SUBJECT-
PRIORITY DYNAMIC AF
AT AF-C MODE If you select “1”, Closest-subject Priority Dynamic AF is
used in AF-C mode.
0: AE/AF LOCK
(default)
1: AE LOCK ONLY
2: AF LOCK ONLY
3: AE REMAINS
LOCKED
4: AF OPERATION
AE/AF LOCK BUTTON Normally, AE lock (exposure recording) and AF lock
(focus lock) are both applied concurrently when you
press the “AE-L/AF-L” button. However, this can be
changed so that only AE lock or only AF lock is applied,
or so that that the AE lock status is maintained. If the
AE/AF lock is used with the “Maintain AE lock” setting,
pressing the “AE-L/AF-L” button again or releasing the
shutter cancels the lock.
In addition, though the auto focus (AF) normally
operates when the shutter button is pressed down
halfway, you can change this so that AF operates when
the “AE-L/AF-L” button is pressed. (In this case, AF
does not operate when the shutter button is pressed
down halfway.)
0: DISABLED (default)
1: ENABLED COMMAND DIAL
FUNCTIONS Use this setting to change the Main-command dial and
Sub-command dial operation during photography.
0: Main: Changes the shutter speed.
Sub: Changes the aperture.
1: Main: Changes the aperture.
Sub: Changes the shutter speed.
11 0: SINGLE SHUTTER
RELEASE (default)
1: CONTINUOUS
SHUTTER
RELEASE
MULTIPLE EXPOSURE Changing this setting allows you to use continuous
shooting for multiple exposure shots.