KORG sampler - Manual (Page 148)

140
Routing settings and effect set-
tings
The insert effects, master effects, and master EQ have the
same structure in all modes, but the routing settings will
determine how the oscillators of a program or the timbres
of a combination or track of a song will be sent to each
insert effect or master effect. In the pages that follow, we
will explain how you can make routing settings and effect
settings in each mode.
Effect settings for a program
Routing
1 In Program P8: Edit-Insert Effect, select the Routing
page.
2 Use “BUS Select (IFX/Indiv.Out Assign) to specify
the bus (insertion effect) to which the output of the
oscillator will be sent.
L/R: The output will not be sent to the insert effects.
After passing through the master EQ, the sound will be
sent to AUDIO OUTPUT (MAIN) L/MONO and R.
IFX1–5:
The output will be sent to insert effect IFX 1, 2,
3, 4, or 5.
1, 2, 3, 4, 1/2, 3/4:
The output will be sent to AUDIO
OUTPUT (INDIVIDUAL) 1, 2, 3, or 4. It will not be sent
to the insert effects, the master effects, or the master
EQ.
Off:
The output will not be sent to AUDIO OUTPUT
(MAIN) L/MONO, R, or to (INDIVIDUAL) 1, 2, 3, 4.
(After passing through the master effects, it will be out-
put from AUDIO OUTPUT (MAIN).) Select this when
you wish to connect the output to the master effects in
a series connection at the send levels specified by
“Send 1 (MFX1)” and “Send 2 (MFX2).”
3 OSC MFX Send specifies the send level from each
oscillator to the master effects.
This can be set only when “BUS Select (IFX/Indiv.Out
Assign)” is either L/R or Off.
If “BUS Select (IFX/Indiv.Out Assign)” is set to IFX1–5,
the send level to the master effects is set by “Send 1”
and “Send 2” (Insert FX page) after the signal passes
through the insert effects.
Insert effects
4 Select the Insert FX page.
5 For IFX1–5, select the effect type for each insert effect.
When you press the popup button, all effects will be
displayed, organized into six categories. Use the
pages located at the left to select a category, and select
an effect from that category on the LCD screen.
Effects 000–089 can be selected for IFX1, 2, 3, 4, 5, and
MFX1 and 2.
Effects 090–102 are double-size effects, and require
twice the processing area of other effects. These can
be selected for IFX2, IFX3, and IFX4.
You can use the “Copy Insert Effect” page menu com-
mand to copy effect settings from another program
etc. Also, you can use “Swap Insert Effect” to
exchange (for example) IFX1 and IFX5.
6 Press the ON/OFF button to turn on the insert effect.
Each time you press the button, the insert effect will be
switched on/off. When OFF, the result will be the same
as when 000: No Effect is selected. The input sound
will be output without change.
7 Make “Chain” settings.
If the “Chain” check box is checked, the insert effect
will be connected in series. Since the output of the
oscillator is being sent to IFX1 in 2, making settings as
shown in the diagram 4 would connect all five inser-
tion effects IFX1
→
IFX2
→
IFX3
→
IFX4
→
IFX5 in
series, so that these effects would be inserted into the
output of the oscillator.
8 Make settings for “Pan (CC#8),” “BUS Sel. (BUS
Select),” “Send 1,” and “Send 2” for the sound after it
has passed through the insert effects.
If the insert effects are chained, these settings will
apply after the last IFX.
“Pan”: Sets the pan. This is valid only when BUS Sel. is
L/R.
“BUS Sel.” (BUS Select):
Specifies the output destina-
tion. Normally you will set this to L/R. If you wish to
send the sound that has passed through the insert
effects to AUDIO OUTPUT (INDIVIDUAL) 1–4, select
1–4, 1/2, or 3/4.
“Send 1”, “Send 2”:
Sets the send levels to the master
effects. For this example, set this to 127.
9 Select the IFX1–5 pages, and set the parameters for
each of the selected effects.
For details on the parameters of each effect ( ☞PG
p.187–).