Kenwood VR-9080 - Manual (Page 6)

6 EN
THX DOLBY VIRTUAL STEREO INPUT MODE
BASS BOOST DSP ACTIVE EQ DIMMER
MULTI CONTROL LISTEN MODE
INPUT
SELECTOR
VOLUME CONTROL
AV AUX/GAME
SOUND TONE SETUP
BAND
AUTO
/MONO
MEMORY
/ENTER
A SPEAKERS B
PHONES
THX
96kHz fs
ACTIVE EQ
DOLBY DIGITAL
DTS
DSP
S VIDEO VIDEO L-AUDIO-R
L
SL S SB SR
C R
SP MUTE
6CH INPUT
DIGITAL DOLBY DIGITAL EX
DOLBY EX
DOLBY PL II x
DOLBY H
DOLBY VS DTS 96/24
ES MATRIX6.1
ES DISCRETE6.1
STEREO
96kHzfs
LOUDNESS NEO:6
SLEEP
CLIP
AUTO DETECT
AUTO
MEMORY
STEREO
TUNED
SW
LFE
A B
THX
Surround EX
DSP MODE
SETUP MIC
POWER
-ON –OFF
Names and functions of parts
Main unit
1 POWER ON/OFF key )
(For KRF-X9090D)
Use to turn the main power ON/OFF.
2 (POWER ON/STANDBY) key )
Use to turn the power ON/STANDBY.
Standby indicator
3 SPEAKERS A/B keys ¶
Use to turn the A/B speakers on or off.
4 Surround LED (light-emitting diode)
indicators
THX indicator
fl
Lights when the THX mode has been chosen.
THX mode may or may not be activated
depending upon the applicable playback
mode.
96kHz fs indicator
‚
Lights when the receiver is in the 96kHz
LPCM playback mode.
ACTIVE EQ indicator
•
Lights when the receiver is in the ACTIVE EQ
mode.
DOLBY DIGITAL indicator
fl
Lights when the receiver is in the Dolby
Digital mode.
DTS indicator
‡
Lights when the receiver is in the DTS mode.
DSP indicator
‡
Lights when the receiver is in the DSP mode.
5 INPUT SELECTOR key ¶
Use to select input sources.
6 VOLUME CONTROL knob ¶
7 SETUP MIC jack )
Use for SETUP MIC.
8 PHONES jack ª
Use for headphone listening.
9 THX key fl
Use to switch the status of THX.
DOLBY VIRTUAL key
°
Use to select the Dolby Virtual Speaker and
the Dolby Headphone setting.
STEREO key
‡
Use to switch the listen mode to STEREO.
INPUT MODE key
8
Use to select the Input mode.
BASS BOOST key
ª
Use to select BASS BOOST setting.
DSP key
‡
Use to select any of the DSP mode.
ACTIVE EQ key
•
Use to select ACTIVE EQ setting.
DIMMER key
Use to adjust the brightness of the display.
q
Use to select the REC MODE. º
Standby mode
While the standby indicator is lit, a small amount of power is supplied to
the system to back up the memory. This is called standby mode. Under the
condition, the system can be turned ON by remote control unit.
0 SOUND key ·
Use to adjust the sound quality and the
ambience effects.
TONE key
ª
Use to switch the status of TONE control.
BAND key
⁄
Use to select the broadcast band.
AUTO/MONO key
⁄
Use to select the auto or manual tuning
mode.
! SETUP key )
Use to select the speakers' settings etc.
MEMORY/ENTER key
Use to store radio stations in the preset
memory.
⁄
Use to establish a selection.
@ 5/∞ keys )
Use for selection adjustments during sound,
setup and preset channel functions.
# MULTI CONTROL knob
Use to control a variety of settings.
$ LISTEN MODE knob fl
Use to select the listening mode.
% AV AUX/GAME key (¶
Use to switch the input to AV AUX or GAME.
^ AV AUX (S VIDEO, VIDEO, L-AUDIO-R)
jacks (
Display
* Input channel indicators
Output channel indicators
AUTO indicator
MEMORY indicator
STEREO indicator
TUNED indicator
Frequency display
Input display
Preset channel display
Surround mode display
Speaker
indicators MUTE
indicator CLIP
indicator Input mode
indicators Listen mode indicators
SLEEP indicator
* Input channel indicators
Input channel indicators
light up according to the
incoming audio signals.
"S" indicator will light up
when the surround
component of the audio
signals is only 1 channel.
The figure is the view when the front cover is open .
CAUTION
The power in this equipment will not be completely cut off from the AC
wall outlet when the main switch is turned OFF.
05.7.16, 0:48 PM 6