Kenwood VR-9080 - Manual (Page 25)

25 EN
3 Measure the distance from the listening position to each of
the speakers.
Jot down the distance to each of the speakers.
Distance to Front Left Speaker (L)
: ____ feet (meters)
Distance to Center Speaker (C) : ____ feet (meters)
Distance to Front Right Speaker (R) : ____ feet (meters)
Distance to Surround Right (SR) : ____ feet (meters)
Distance to Surround Back Right (SBR) : ____ feet (meters)
Distance to Surround Back (SB)
: ____ feet (meters)
Distance to Surround Back Left (SBL) : ____ feet (meters)
Distance to Surround Left (SL)
: ____ feet (meters)
Distance to Subwoofer (SW) : ____ feet (meters)
• If you have selected “SB NML/THXx1” or ”SB LARGEx1”,
“SBR” and “SBL” are not appeared but “SB” is appeared on the
Display.
4 Use the 5/∞ keys or MULTI @/# keys to select the speakers
and the MULTI CONTROL knob or MULTI %/fi keys to adjust
the distance to the Front Speakers.
The speaker indicator to be adjusted blinks.
L
SL S SB SR
C R
SP MUTE
A B CLIP SW
LFE
STEREO
Indication in feet
• The allowable setting range is 0.1 to 30.0 feet (0.03 to 9.14 m),
adjustable in 0.1 foot (about 0.03 m) increments.
5 Repeat steps 4 to input the distance for each of the speakers.
6 Press the MEMORY/ENTER key or the ENTER key to return to
the “SP DISTANCE“ display.
• The speakers you have selected should appear on the display.
Confirm that all the speakers have been correctly selected.
4
Exit the MANUAL SETUP mode.
1 Press the 5/∞ keys or MULTI @/# keys to select the “RE-
TURN“
L R
SP MUTE
A B CLIP
SL S SB SR
STEREO
2 Press the MEMORY/ENTER key or the ENTER key to return to
the “MANUAL SETUP“ display.
Preparing for surround sound
Other settings
1
Adjust the Subwoofer RE-MIX.
1 Press the 5/∞ keys or MULTI @/# keys to select the “SW RE-
MIX“ and press the MEMORY/ENTER key or the ENTER key.
2 Use the MULTI CONTROL knob or MULTI %/fi keys to select
the appropriate Subwoofer re-mix setting.
If “SW RE-MIX ON” is selected as the subwoofer re-mix setting,
the low frequencies are enhanced by adding the low frequencies
of other channels to the subwoofer channel depending on the
speaker setup.
1 SW RE-MIX ON : Subwoofer re-mix setting mode to the
receiver is ON.
2 SW RE-MIX OFF : Subwoofer re-mix setting mode to the
receiver is OFF.
• If Subwoofer is turned off or “FRNT NML/THX” is selected at the
Front Speaker setting, Subwoofer re-mix setting is not visible.
• By selecting “SW RE-MIX OFF”, the low frequencies will play
through the Front Speakers only.
This selection is preferred by THX.
3 Press the MEMORY/ENTER key or the ENTER key to accept
the setting.
2
Select the CROSSOVER frequency.
CROSSOVER function is to adjust the receiver’s audio output charac-
teristics with the speakers’ characteristics which differs depending
on the size of the speakers. You will be able to enjoy a more natural
and dynamic sound experience even with small size speakers.
1 Press the 5/∞ keys or MULTI @/# keys to select the “CROSS
OVER“ and press the MEMORY/ENTER key or the ENTER key.
• CROSSOVER function will not be available when “LARGE” is
selected for all the speakers in step 1 and “SW RE-MIX OFF”
is selected . £
2 Use the MULTI CONTROL knob or MULTI %/fi keys to select
the CROSSOVER frequency.
1 FREQ. : 40Hz
2 FREQ. : 60Hz
3 FREQ. : 80Hz-THX
4 FREQ. : 100Hz
5 FREQ. : 120Hz
6 FREQ. : 150Hz
• If you have THX certified speakers, select ”FREQ.:80Hz-THX”.
L R
SP MUTE
A B CLIP
STEREO
3 Press the MEMORY/ENTER key or the ENTER key to accept
the setting.
3
Adjust the distance between left and right Surround Back
speaker.
This mode is avaiable only when “SB NML/THXx2“ or “SB LARGEx2“
has been selected in Surround Back Speaker setting.
1 Press the 5/∞ keys or MULTI @/# keys to select “SB SPAC-
ING“ and press the MEMORY/ENTER key or the ENTER key.
Continued to next page.
05.7.16, 1:25 PM 25