Kenwood VR-9080 - Manual (Page 40)

40 EN
Dimension mode (Pro Logic II x Music mode and Pro Logic II
Music mode only)
When listening to music with certain recordings, you will also be able to achieve
a suitable balance from all the speakers by adjusting the dimension mode.
1 Press the SOUND key, then press the 5/∞ keys or MULTI @/#
keys until “DIMENSION” appears on the display.
2 Use the MULTI CONTROL knob or MULTI %/fi keys to adjust the
soundfield towards the rear or the front.
Soundfield is adjusted towards the front.
L R
LFE
SP MUTE
A B CLIP DOLBY PL II x
AUTO DETECT
Soundfield is adjusted towards the rear.
L R
LFE
SP MUTE
A B CLIP DOLBY PL II x
AUTO DETECT
3 Press the SOUND key again to return to the input indication.
Center Width mode (Pro Logic II x Music mode and Pro Logic II
Music mode only)
Center width adjustment allows you to enjoy an enhanced sound when
listening to music through center image from only center speaker, or left
and right speakers or various combinations adjustments.
1 Press the SOUND key, then press the 5/∞ keys or MULTI @/#
keys until “CENTER WIDTH” appears on the display.
• The CENTER WIDTH indication scrolls across the display.
• When the center speaker is switched OFF, this mode will not be
effective.
2 Use the MULTI CONTROL knob or MULTI %/fi keys to adjust the
left-center-right output.
Center image will be heard from center speaker only.
L
S SB
R
LFE
SP MUTE
A B CLIP DOLBY PL II x
AUTO DETECT
Center image will be heard from left and right speakers only.
L
S SB
R
LFE
SP MUTE
A B CLIP DOLBY PL II x
AUTO DETECT
• When in other position, center image from center speaker, left and
right speakers can be heard simultaneously with various combinations.
3 Press the SOUND key again to return to the input indication.
Ambience effects
Center Image mode (Neo:6 Music mode only)
In the CENTER IMAGE setting mode of the Neo:6 Music listen mode, it
is possible to enhance the center channel audio by adjusting the center
signal component.
1 Press the SOUND key, then press the 5/∞ keys or MULTI @/#
keys until “CENTER IMAGE” appears on the display.
L R
SP MUTE
A B CLIP
STEREO NEO:6 AUTO DETECT
• When the center speaker is switched OFF, this mode will not be
effective.
2 Use the MULTI CONTROL knob or MULTI %/fi keys to adjust the
left-center-right output.
L
S SB
R
LFE
SP MUTE
A B CLIP
NEO:6 AUTO DETECT
• Adjust the center component level.
3 Press the SOUND key again to return to the input indication.
Dual Mono mode (Dolby Digital mode only)
When the Dolby Digital source have Multiplex sound, you can select
Main / Sub sound for Audio output.
1 Press the SOUND key, then press the 5/∞ keys or MULTI @/#
keys until “DUAL MONO” appears on the display.
• This can be selected only if CD/DVD, DVD/6CH, VIDEO 2 or VIDEO 3
is selected as the source and the LISTEN mode is set to “Dolby
Digital”.
2 Use the MULTI CONTROL knob or MULTI %/fi keys for the
following selection.
1 Main : Multiplex Main channel output.
2 Sub : Multiplex Sub channel output.
3 Main + Sub : Multiplex Main + Sub channel output.
4 Stereo : M a i n c h a n n e l f r o m t h e l e f t s p e a k e r .
/ Sub channel from the right speaker.
LFE
SP MUTE
A B CLIP
DIGITAL DOLBY DIGITAL STEREO AUTO DETECT
• The adjustment item is displayed for approximately 20 seconds.
3 Press the SOUND key again to return to the input indication.
96kHz LPCM playback
The receiver is compatible with the 96kHz LPCM playback. To play a
96kHz DVD, set the listen mode other than DSP mode.
(96kHz fs indicator lights up)
• When the listen mode is set to DSP mode, the listen mode will
automatically be Stereo.
05.7.16, 1:28 PM 40