Sanyo LC-2430 - Manual (Page 56)

E52
REN Number:
The Ringer Equivalence Number (REN) assigned to each
terminal device provides an indication of the maximum number
of terminals allowed to be connected to a telephone interface.
The REN number of this unit is located on the bottom of the
base unit. The termination on an interface may consist of any
combination of devices subject only to the requirement that the
sum of the Ringer Equivalence Numbers of all the devices does
not exceed 5.
CAUTION
This Product is intended for use in CANADA only. Sale or use in
other countries may violate local laws.
Cordless telephones use radio frequencies to allow mobility.
This affects the performance of your unit.
1. NOISE
Electrical pulse noise is present in most homes at one time or
another. This is most intense during electrical storms. Certain
kinds of electrical equipment, such as light dimmers, fluorescent
bulbs, motors, fans, etc., also generate pulse noise.
Because radio frequencies are susceptible to this, you may on
occasion hear pulse noise through the handset. This is usually
only a minor annoyance and should not be interpreted as a
defect of the unit.
2. RANGE
Because radio frequencies are used, the location of the base
station can affect the operating range of the unit. Try several
locations and choose the one that gives the clearest signal to
the handset. (Turning in a circle while holding the handset may
also increase the operating range.)
3. INTERFERENCE
Electronic circuits activate a relay to connect the unit to your
telephone line. These electronic circuits operate in the radio
frequency spectrum. While several protection circuits are used
to prevent unwanted signals, there may be periods when these
unwanted signals enter the base station. You may hear click or
hear the relay activate when you are not using the cordless
handset. If this occurs frequently, you can minimize or eliminate
the problem by lowering the height of the base station or
relocating the base station. It may also be helpful to change the
operating channel and/or the security code setting.
Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
NOTICE:
Privacy of communications may not be ensured when using this
telephone. Other devices, including other cordless telephone
telephones, may interfere with the operation of this cordless
telephone or cause noise during operation. Units without coded
access may be accessed by other radio communication
systems. Cordless telephones must not cause interference to
any licensed radio service.
The Industry Canada Label identifies certified equipment. This
certification means that the equipment meets certain
telecommunications network protective, operational and safety
requirements. The ministry does not guarantee that the
equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be
installed using an acceptable method of construction.
In some cases, the company’s inside wiring associated with
single-line individual service may be extended by means of a
certified connector assembly (telephone extension cord). The
customer should be aware that compliance with the above
conditions may not prevent degradation of service in some
situations.
Repairs to certified equipment should be made by an authorized
Canadian maintenance facility designated buy the supplier. Any
repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications
company cause to request that the user disconnect the
equipment.
The user should ensure for his own protection that the
electrical ground connections of the power utility, telephone
lines and internal metallic water pipe system, if present, are
connected together. This precaution may be particularly
important in rural areas.
CAUTION
Users should not attempt to make such connections
themselves, but should contact the appropriate electrical
inspection authority, or electrician, as appropriate.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the product.
This symbol on the product is used to identify the following
important information. Use only with specified SANYO power
adaptor.
TECHNICAL INFORMATION
CLT2430 5th 8/9 8/10/00 4:29 PM Page 56