JVC SP-THS55F - Manual (Page 53)

Masterpage:Right+
Filename [TH-R1R3EU_07Timer Recording.fm]
Page 50Monday, 28 March 2005 21:23
TIMER RECORDING
50
You can programme this unit to timer record as many as
8 programmes up to 30 days in advance. If you do not know the
S
HOW V IEW number for the programme you wish to record, use the
following procedure to set your unit to timer record the programme.
1
Load a recordable disc.
● For details, refer to APlacing A DiscB (A pg. 5).
2
Press PROG to display
the
APROGRAMME
CHECK B screen.
● When APROGRAMME
FULL DELETE
UNWANTED TIMER
PROGRAMME
B appears
on the TV screen, you
need to cancel some of
the reserved
programmes.
3
Press selection keys
repeatedly to select
ANEW TIMER
PROGRAMME
B, then
press ENTER.
4
Press selection keys to
set the desired date
(
ADATEB), then press E.
5
Press selection keys to
set the desired start
time (
ASTARTB), then press E.
● Each press of F G increases/decreases the start time in
1 minute interval.
● To increase/decrease the start time in 30 minutes interval,
press and hold
F G.
6
Press selection keys to set the desired stop time ( ASTOPB),
then press E.
● Each press of F G increases/decreases the stop time in
1 minute interval.
● To increase/decrease the stop time in 30 minutes interval, press
and hold
F G.
7
Press selection keys to set the desired channel ( ATV PROGB),
then press E.
8
Set the other recording options as required.
● Refer to step 6 in AS HOW V IEW Timer Programming B (A pg. 49).
9
Press ENTER to access the Programme Confirmation screen.
10
Press ENTER to complete the timer programming.
● To programme another timer, repeat steps 2 - 10.
11
Press TIMER j to engage the unit’s timer mode.
● The unit turns off automatically and j appears on the front
display panel.
● To disengage the timer mode, press TIMER j again.
NOTES:
● TV DIRECT mode is activated when the unit turns on
automatically during timer recording.
● When two successive programmes are recorded with the
AManual Timer ProgrammingB function, the ending of the first
programme or the beginning of the second programme may not
be recorded.
● If the copy limited programme is received during timer recording,
the unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.
VPS/PDC Recording
Now available from some TV stations, PDC (Programme Delivery
Control) and VPS (Video Programme System) are services
designed to assure safe, accurate timer recording. With this
system, special code signals are transmitted together with the
audio/video signals. These code signals control your unit and have
precedence over the advertised times you may have preset into the
timer. This means that your unit will start and stop recording when
the preset TV programmes actually start and end^even if the
broadcast time of a preset TV programme is changed.
NOTES:
● When you use Manual Timer Programming, set the start time
(VPS or PDC time) exactly as advertised in the TV listing. A
different time than advertised will result in no recording.
● VPS/PDC recording is also possible via the [L-1 INPUT/
OUTPUT] connector.
How to check if the station being received transmits a VPS/
PDC signal
A Press DISPLAY for 5 or more seconds. AVPS/PDCB is displayed
on the front display panel. If a VPS/PDC signal is detected from
the station,
AVPS/PDCB will stop blinking. If no VPS/PDC signal
is detected from the station, AVPS/PDCB will blink at a slower
rate.
B Press DISPLAY again to return to normal display.
Manual Timer Programming
● Turn on the unit.
● Turn on the TV and select an input mode such as EXT1.
● Set the remote control selector switch to AUDIO.
● Press DVD on the remote control.
● Make sure that the unit’s built-in clock is set properly.
1 2 3
4 5 6
7 8 9
0
VOL
SAT
TV
AUDIO
PROG
DVD
DISPLAY
TIMER j
(FGDE)
ENTER
Selection Keys
19:00 - 20:00
22:00 - 22:30
13:30 - 14:00
16:00 - 17:00
PROG
PROGRAMME CHECK
++++++++++++++++++ NEW TIMER PROGRAMME ++++++++++++++++++
DISC TIMER PRGM
SELECT WITH [CURSORS]
THEN PRESS [ENTER] OK
SELECT
EXIT
05/07 SAT 44 SP
10/07 THU 10 XP
11/07 FRI 26 LP
WEEKLY
11/07 FRI 33 LP
ON
OFF
OFF
ON
DATE START-STOP TV PROG VPS/PDC REC MODE DAILY/WEEKLY
LP
VTM 10 20:30 20:00
TIMER PROGRAMME
DATE START STOP TV PROG
05/07 SAT
DAILY/WEEKLY VPS/PDC
OFF
NAME
SET TIMER PROGRAMMING WITH [CURSORS]
THEN PRESS [ENTER]
REC MODE
CONFIRM
SELECT PROG
EXIT
Satellite Receiver Users
To record a satellite broadcast using Manual Timer
Programming:
A Perform Manual Timer Programming.
B Set the satellite receiver to the appropriate channel for
recording.
● Leave the satellite receiver’s power on.
TH-R1R3EU_00.book Page 50 Monday, March 28, 2005 9:23 PM