JVC BR-D95U User Manual
Page 29
56
Menu SW
On-screen
Counter
On-screen
No.
display
display
display
320
PREROLL TIME
0
0SEC
[5]
[5SEC]
15
15SEC
323
PREROLL END
0
STANDBY-ON
MODE
[1]
[STILL]
328
EDIT POINT
0
DISABLE
CLEAR
[1]
[ENABLE]
340
SEARCH SPEED
[0]
[x 32]
1
x 17
3
x 6
351
PREREAD
[0]
[VID-OFF/
AUD-OFF]
1
VID-ON/
AUD-OFF
2
VID-OFF/
AUD-ON
3
VID-ON/
AUD-ON
352
AUD PREREAD
[0]
[NORMAL]
TIMING
1
OFF SET
[ ] : Factory setting
5-2 MENU SWITCH SETTING CONTENT
5 MENU SWITCH SETTING DETAILS
Sets the preroll time when the [PREROLL] button is
pressed.
The preroll time can be selected from 0 second to
15 seconds.
Selects whether the edit point data is cleared after
performing the edit
DISABLE : The edit point is not cleared.
ENABLE : The edit point is cleared.
Selects whether or not the preread function is
activated. Video and audio preread functions
can be set independently.
VID-OFF/AUD-OFF : Both video and audio
preread are disabled.
VID-ON/AUD-OFF : Only video preread is
enabled.
VID-OFF/AUD-ON : Only audio preread is
enabled.
VID-ON/AUD-ON
: Both video and audio
preread are enabled.
* When using the [REC] button to start
recording, be sure to set this switch to “VID-
OFF/AUD-OFF”.
...
Selects the maximum search speed when using
the search dial.
X32 : Maximum search speed is +/-32 times
normal.
X17 : Maximum search speed is +/-17 times
normal.
X6 : Maximum search speed is +/-6 times
normal.
...
Selects which operation mode is engaged after
preroll is executed.
STANDBY-ON : Engages the Standby ON mode.
STILL
: Engages the Still mode.
Selects whether or not to apply correction during
audio preread. Correction is based on output audio
phase delay set with the audio control menu
phase according to the delay of the
connected video device.
Item
Content
Setting
...
...
57
[ ] : Factory setting
5-2 MENU SWITCH SETTING CONTENT
5 MENU SWITCH SETTING DETAILS
Menu SW
On-screen
Counter
On-screen
No.
display
display
display
Selects whether or not editing aborts when the
audio condition degrades during PREROLL.
OFF : Does not stop editing.
ON : Stops editing. Error message is shown on the
counter display.
357
DIAG AT
[0]
[OFF]
POWER ON
1
ON
359
JOG FEELING
[0]
[TYPE-1]
(REMOTE)
1
TYPE-2
2
TYPE-3
3
TYPE-4
4
TYPE-5
363
CONTROLLER
[0]
[DEFAULT]
SELECT
1
RM-450
2
NOT DEFINED
3
NOT DEFINED
4
NOT DEFINED
5
NOT DEFINED
6
NOT DEFINED
7
NOT DEFINED
367
EDIT INTER-
[0]
[OFF]
RUPTION
1
ON
(525)
368
STARTING PIC
[0]
[OFF]
FREEZE
1
ON
Alters the operation “feel” of the connected
editing controller's jog dial.
Five settings (TYPE-1 (0) to TYPE-5 (4)) are
available.
This menu changes the characteristics of the VCR
to match specific types of controllers.
DEFAULT : Normally set to this position. This
position is ready for standard editing
controllers.
RM-450
: Set to this position for an editing remote
controller which outputs JOG
commands for synchronization.
(e.g.) SONY RM-450
NOT DEFINED - TYPE-7: Not defined.
Selects playback pictures or a still image as the
video output until the servo locks.
OFF : A playback picture is displayed. The picture
may be noisy until the servo stabilizes.
ON : A still image is displayed. This changes to
playback video when the servo stabilizes.
Selects whether or not self-diagnosis is executed
when the power is turned on.
OFF: Self-diagnosis is not executed.
ON : Self-diagnosis is executed.
However, if no tape is loaded when the power is
turned on, self-diagnosis does not take place.
While diagnostics are running (“DIAGNOSTIC”
blinks on the screen), you cannot load a cassette.
Do not try to forcibly load it.
After completion of diagnostics, a warning
indication is shown if there is an abnormality.
Refer to “Warnings with Indicators” on page 145.
Item
Content
Setting
* When this menu switch is set to “ON” and
playback starts from a still image containing the
block noise, still images containing block noise
are output until the servo indicator lights.
To avoid this, obtain a clear still image before
starting playback (using the jog dial or frame
advance/reverse buttons).