Rear panel – Maxtor pmn User Manual

Page 7

PANTILT COMMAND SETUP : When PTZ camera whose protocol is already incorporated into this DVMR
system (Default PTZ camera) is connected to this DVMR, just select model of PTZ camera in
PANTILT COMMAND SETUP. If user want to connect PTZ camera which is not one of Default PTZ
camera, users must input protocols of PTZ camera or speed dome camera by themselves in USER
DEFINE SETUP.
For detail procedure, refer to manual for incorporating protocol of PTZ camera into DVMR system.

HDD INFORMATION

HDD DATA LIST : Shows general information of HDD.

HDD AUTO DETECT : Allows to detect HDD just in case first HDD search after purchase failed.

5. Operation

3. NOTE for scheduled recording :
When scheduled recording is set, DVMR unit does not record before the set time. It only starts recording at

01:00-03:00 ON
04:00-05:00 ON

Just record from 1 to 3 and from 4 to 5, and does not record for the rest hours.

01:00-03:00 OFF
04:00-05:00 OFF

Not record from 1 to 3 and from 4 to 5, and records for the rest hours.

01:00-03:00 ON

04:00-05:00 OFF

Just record from 1 to 3 (When both ON and OFF are set, priority is on ON.)

START time and ends at END time.

PANTILT COMMAND SETUP

SELECT , PRESS ENTER

COMMAND TYPE : USER DEFINE
485 BAUDRATE : 9600 BPS
USER DEFINE SETUP

1. DRX-502A
2. AECD-2000

3. HMC-250
4. PELCO D TYPE
3.USER DEFINE

SYSTEM SETUP

DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT

BUZZER SETUP
ID/PW SETUP
SCHEDULE REC
SETUP
PANTILT CMD SETUP
HDD INFORMATION
MARK IMAGE SETUP
PRODUCT ID

3.Unit Description

5. Camera Connection

6. LOOP Output

7. VCR Connection

8. MONITOR Connection

10. S-VHS Connection

3. AUDIO : 4 Input and 1 output

2. PAN/TILT Controller, Sensor Input/Output

1. RS-232C Port Connection

4. LAN (TCP/IP)

9. VGA Connection

11. D/C Power Connection

NOTICE : When connecting with other applications, be sure to turn off the system.

ALL ABOUT IMAGE RECOGNITION & PROCESSING

Rear Panel

DC 12V

ETHERNET

RS-232C

VCR

CH1

CH2

CH3

CH4

MONITOR

LOOP

Co
m

m
P

V
G
A

Procedure to control PTZ camera while you see live picture
1. Default PTZ camera : First select PTZ camera model connected to DVMR unit in the PANTILT COMMAND
SETUP menu. In live view mode, press [P/T] button and set CAM (Starts from 000) at camera ID which
is set on PTZ camera (DIP switch on PTZ camera) before you connect it to DVMR unit. Then select
command you want to execute using [LEFT] and [RIGHT] buttons. While you press [PLAY] button,
command you selected is executed.
2. USER DEFINE : In case you input protocols of PTZ camera which is not one of Default cameras, select
USER DEFINE in PANTILT COMMAND SETUP. Then press [P/T] button and set CAM (Ranges from
001 to 004) at any one from 001 to 004. CAM number must be the same as CH number which you set
when you input protocol of PTZ camera in USER DEFINE. Using [LEFT] and [RIGHT] button, select
command you want to execute and press [PLAY] button to execute selected command. While you press
[PLAY] button, command you selected is executed.

PAN/TILT COMMAND SETUP

AUDIO

SPK MIC4 MIC3 MIC2 MIC1

1 2 3 4 5 6 7 8 9 10

FUNCTION

6 ALARM GND
7 ALARM D4
8 ALARM D3
9 ALARM D2

10 ALARM D1

1 RS 485 D-
2 RS 485 D+
3 RELAY COM
4 RELAY NC
5 RELAY NO