Marantz SR6003 - Manual (Page 55)

52
ENGLISH
BASIC
CONNECTIONS
BASIC OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
ADV
ANCED
OPERA
TION
5. After selecting the fi rst character to be entered,
press the MEMORY or ENTER button, or press
the MEMO button on the remote controller.
The entry in this column is fi xed and the next
column starts to fl ash. Fill the next column the
same way.
To move back and forth between the characters,
press the 1 / 2 cursor buttons.
Note:
• Unused columns should be filled by entering
blanks.
6. To save the name, press the MEMORY or
ENTER button on the front panel, or press the
MEMO button on the remote controller for more
than 2 seconds.
Instead of using the 3 and 4 cursor buttons to
select characters, characters can be input from
the numeric keys of the remote controller. See
the below table for a correspondence between
characters and numeric keys.
Ten keypad Press, press again, press again, etc.
1 A → B → C → 1 → A
2 D → E → F → 2 → D
3 G → H → I → 3 → G
4 J → K → L → 4 → J
5 M → N → O → 5 → M
6 P → Q → R → 6 → P
7 S → T → U → 7 → S
8 V → W → X → 8 → V
9 Y → Z → space → 9 → Y
0 – → + → / → 0 → –
NAME INPUT OF THE PRESET STATION.
This function allows the name of each preset channel
to be entered using alphanumeric characters.
Before name inputting, you need to store preset
stations with the preset memory operation.
5. 2. 5. 6. 4.
4.
5.
2.
5.
6.
1. Recall the preset number to be inputted name
with the method described in “Recalling” a
preset station.
2. Press the MEMORY button on the front panel
or press the MEMO button on the remote
controller for more than 3 seconds.
3. The left most column of the station name
indicator fl ashes, indicating the character entry
ready status.
4. When you press the 3 or 4 cursor buttons
on the front panel or the remote controller,
alphabetic and numeric characters will be
displayed in the following order:
A ↔ B ↔ C ... Z ↔ 1 ↔ 2 ↔ 3 ..... 0 ↔ – ↔ +
↔ / ↔ (Blank) ↔ A
UP →
← DOWN
SORTING PRESET STATIONS
If you have stations memorized, and there is a gap in
the sequential order:
I.e. the stations are stored as follows
1) 87.1 MHz
2) 93.1 MHz
3) 94.7 MHz
10) 105.9 MHz
(notice there is no stations programmed for presets
for 4-9), you can have preset 10 become preset 4:
To sort the numbers, press and hold the MEMORY
and the
4 cursor buttons.
“PRESET SORT” will appear on the display and
sorting will be done.
CLEARING STORED PRESET STATIONS
You can remove preset stations from the memory
using the following procedure.
3. 2.
2.
3.
1. Recall the preset number to be cleared with
the method described in “Recalling” a preset
station.
2. Press the MEMORY button on the front panel
or press the MEMO button on the remote
controller.
3. The stored preset number blinks in the display
for 5 seconds. While blinking, press the CLEAR
button on the front panel or the CL button on the
remote controller.
4. “xx CLEAR” appears on the display to indicate
that the specified preset number has been
cleared.
Note:
• To clear all stored preset stations, press and hold the
T-MODE and the ENTER buttons for two seconds.