Marantz SR6003 - Manual (Page 25)

ENGLISH
22
BASIC
CONNECTIONS
BASIC OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
ADV
ANCED
CONNECTIONS
a RS-232C
Connect an external control device or other device for
servicing. (Use a straight cable for the connection.)
s DC OUT (DC TRIGGER)
External devices can be controlled from the unit
by connecting them to the DC OUT terminal (12 V
44mA max).
GND
+12V
d FLASHER IN
This unit can be controlled by connecting a control
box or other control device to this unit.
GND
Signal
R R R R L L L L R R L L L L R R
AUDIO AUDIO
INPUT 2 INPUT 2(DVD)
INPUT INPUT 1(TV)
MONITOR OUT MONITOR OUT C CB B //P PB Y Y VCR OUT VCR OUT VCR IN VCR IN((3 3)) TV TV((1 1)) DVD DVD((2 2)) DSS DSS((4 4))
S-VIDEO S-VIDEO
VIDEO VIDEO
OUTPUT 2 OUTPUT 2 OUTPUT 1 OUTPUT 1 INPUT 3 INPUT 3( (VCR VCR) ) INPUT 2 INPUT 2( (DVD DVD) ) INPUT 1 INPUT 1( (TV TV) )
FM FM ( (75 75 Ω Ω)) GND GND AM AM ANTENNA ANTENNA
R R SR SR
C C
SW SW SBR SBR
SL SL SBL SBL L L
PRE OUT PRE OUT
ON ON
RS-232C RS-232C SPEAKER C SPEAKER C
OFF OFF
CENTER CENTER SURROUND SURROUND FRONT A FRONT A FRONT B FRONT B SURROUND BACK SURROUND BACK
SPEAKER C/ SPEAKER C/ ZONE SPEAKER A ZONE SPEAKER A
R R
L L
CD/CDR CD/CDR
OUT OUT IN IN OUT OUT IN IN
TAPE TAPE TV TV DSS DSS VCR VCR DVD DVD
OUT OUT OUT OUT IN IN
REMOTE CONT. REMOTE CONT.
IN IN
OUT OUT OUT OUT 3 3 1 1
4 4
DIGITAL IN DIGITAL IN
5 5
2 2
REC/ZONE B REC/ZONE B DIGITAL DIGITAL
DC OUT DC OUT
FLASHER IN FLASHER IN
7.1CH INPUT 7.1CH INPUT ( (AUX 2 AUX 2) )
SL SL C C L L SBL SBL
R R SR SR SW SW SBR SBR
ZONE A ZONE A
SPEAKER SYSTEMS SPEAKER SYSTEMS FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS
FRONT A + B : 8 OHMS FRONT A + B : 8 OHMS
SWITCHED SWITCHED
1.25A 150W
1.25A 150W
UNSWITCHED UNSWITCHED
1.25A 150W 1.25A 150W
AC OUTLETS AC OUTLETS
120V 60Hz 120V 60Hz
DC OUT DC OUT
FLASHER IN FLASHER IN
RS-232C RS-232C
a
d s
CONNECTING OTHER EQUIPMENT
L L
OUTPUT 2 OUTPUT 2 OUTPUT 1 OUTPUT 1 INPUT 2 INPUT 2( (DVD DVD) )
INPUT 3 INPUT 3( (VCR VCR) ) INPUT 1 INPUT 1( (TV TV) )
COMPONENT COMPONENT VIDEO VIDEO
MONITOR OUT MONITOR OUT C CR R // P PR R C CB B // P PB B Y Y C CR R // P PR R C CB B // P PB B Y Y C CR R // P PR R C CB B // P PB B Y Y VCR OUT VCR OUT VCR IN VCR IN((3 3)) VD DVD((2 2)) DSS DSS((4 4))
OUND BACK SURROUND BACK EAKER C/ SPEAKER C/ SPEAKER A ZONE SPEAKER A
REMOTE CONT. REMOTE CONT.
IN IN
OUT OUT OUT OUT 3 3
DIGITAL IN DIGITAL IN
5 5
2 2
REC/ZONE B REC/ZONE B DIGITAL DIGITAL
DC OUT DC OUT
FLASHER IN FLASHER IN
MODEL NO. SR6003 MODEL NO. SR6003
SWITCHED SWITCHED
1.25A 150W 1.25A 150W
UNSWITCHED UNSWITCHED 1.25A 150W 1.25A 150W
AC IN AC IN
AC OUTLETS AC OUTLETS
120V 60Hz 120V 60Hz
SIRIUS SIRIUS
REMOTE CONT. REMOTE CONT.
IN IN
OUT OUT
REMOTE
CONTROL
REMOTE
CONTROL
REMOTE
CONTROL
IN
OUT
IN
OUT
IN
OUT
EXTERNAL INTERNAL EXTERNAL INTERNAL EXTERNAL INTERNAL
1
RC OUT
2
CONNECTING THE REMOTE CONTROL JACKS
DVD player CD recorder
q
You can control other Marantz products through this
unit with the remote controller by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote controller
is received by the remote sensor on this unit. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the remote
control only at the unit. Also, if a Marantz power
amplifi er (some models excluded) is connected to
one of these terminals, the power amplifi er’s, power
switch is synchronized with this unit’s power switch.
Set the REMOTE CONTROL SWITCH on the back of
other units (not the SR6003) to “EXT.” (EXTERNAL)
to use this feature.
CD player
OPTION
w
Whenever external infrared sensors or similar devices
are connected to RC-5 IN of the unit, be sure to
always disable operation of the infrared sensor on the
unit by using the following procedure.
1. Hold down the SURROUND MODE button
and the MENU button on the front panel at the
same time for fi ve seconds.
2. The setting “IR=ENABLE” is shown on the FL
DISPLAY.
3. Press the CURSOR buttons ( 1, 2) to change
this to “IR=DISABLE”.
4. Press the ENTER button. Once this setting
is made, the infrared sensor on the unit is
disabled.
Note:
• Be sure to set to “IR=ENABLE” when external
infrared sensors or similar devices are not connected.
Otherwise, the unit will be unable to receive remote
control commands.
5. To restore the original setting, perform steps 1
to 4 to set to “IR=ENABLE”.