Marantz SR6003 - Manual (Page 19)

ENGLISH
16
BASIC
CONNECTIONS
BASIC OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
BASIC OPERA
TION
BASIC OPERATION
AMP OPERATION
TURNING ON THE UNIT
1. Connect the AC power cable to the wall outlet.
2. Turn the power of the equipment connected to
this unit on.
3. Press the POWER ON/STANDBY button of
this unit. Every time the button is pressed,
the power to this unit toggles between on and
standby.
To activate power using the remote controller,
press the AMP button, followed by the ON
button and SOURCE ON/OFF button of the
remote controller.
SELECTING AN INPUT SOURCE
Before you can listen to any input media, you must
fi rst select the input source on the unit.
Example : DVD
To select DVD, turn the INPUT SELECTOR knob
on the front panel or press the DVD button on the
remote controller two times in a row. After you have
selected DVD, simply turn on the DVD player and
play the DVD.
• As the input source is changed, the new input
name will appear momentarily an OSD information
on the video display. The input name will also
appear in the display, on the front-panel.
• If you use the FUNCTION RENAME feature (see
page 28) , the renamed name appears on the
display.
• As the input is changed, this unit will automatically
switch to the digital input, surround mode,
attenuation, and night mode status which were
entered during the confi guration process for that
source.
• When a video source is selected, the selected
video signal is output from the MONITOR OUT
terminal.
ADJUSTING THE MAIN VOLUME
Adjust the volume to a comfortable level using
the VOLUME control knob on the front panel or
VOLUME + / – buttons on the remote controller.
To increase the volume, turn the VOLUME knob
clockwise or press VOLUME + button on the
remote controller, to decrease the volume, turn
counterclockwise or press VOLUME – button on the
remote controller.
Notes:
• The volume can be adjusted within the range of – ∞
and –71 to 18 dB, in steps of 1 dB.
• However, when the channel level is set as described on
page 34, if the volume for any channel is set at +1 dB
or greater, the volume cannot be adjusted up to 18 dB.
(In this case the maximum volume adjustment range
is “18 dB - Maximum value of channel level)
ADJUSTING THE TONE (BASS & TREBLE)
CONTROL
During a listening session you may wish to adjust the
Bass and Treble Control to suit your listening tastes
or room acoustics.
(Using the remote controller)
To adjust the tone, press the AMP button.
To adjust the bass effect, press BASS + or BASS
– button.
To adjust the treble effect, TREBLE + or TREBLE
– button.
Notes:
• The tone control function is unavailable for the
Source Direct, Pure Direct, Headphone, Dolby
Virtual Speaker mode, and 176.4/192kHz PCM.
• The Tone control function is not available when M-
DAX is being used.
• The tone control function is not available when
ACOUSTIC EQ is being used.
• Additionally, tone control is not available during
Dolby TrueHD, Dolby Digital Plus, or DTS-HD
playback.
TEMPORARILY TURNING OFF THE SOUND
To temporarily silence all speaker outputs such as
when interrupted by a phone call, press the MUTE
button on the remote controller.
This will interrupt the output to all speakers and the
head-phone jack, but it will not affect any recording or
dubbing that may be in progress.
When the system is muted, the display will show
“MUTE” .
Press the MUTE button again to return to normal
operation.
TUNER OPERATION
To operate the unit from the remote controller, press
the TUNE button on the remote controller so that the
tuner mode is engaged.
LISTENING TO THE TUNER
Frequency scan step for AM is selectable.
Default setup is 10 kHz step, if your country’s
standard is 9 kHz step, Press BAND button on the
front panel or BAND button on the remote controller
more than 5 seconds. Scan step will change.
Note:
• Preset memory for the tuner will clear by changing
this setup.
AUTO TUNING
1. 2. 3.
1.
3.
2.
(Using the unit)
1. Turn the INPUT SELECTOR knob to select
“TUNER”.
2. Press the BAND button to select either FM or
AM.
3. Press the 3 or 4 cursor buttons on the front
Panel for more than 1 second to start the auto
tuning function.
4. Automatic searching begins then stops when a
station is tuned in.