Marantz SR6003 - Manual (Page 54)

51
ENGLISH
BASIC
CONNECTIONS
BASIC OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
ADV
ANCED
OPERA
TION
4. You can fast forward the preset stations, press
the 2 continuously.
5. When the desired preset station is received,
cancel the preset scan operation by pressing
the CL button or P.SCAN button on the remote
controller.
PRESET CHANNEL LIST DISPLAY
A complete list of the broadcast channels stored in
this unit can be displayed.
1.
2.
4.
1. Press the TUNE button on the remote controller
twice within two seconds to switch to the
TUNER function.
2. Press INFO button on the remote controller.
3. The list of preset channels will be displayed on
the screen of the TV monitor connected to this
unit.
P R E S E T L I S T
N O . 1 F M 8 7 . 1 0 M H z
N O . 2 F M 9 3 . 1 0 M H z
N O . 3 F M 9 4 . 7 0 M H z
N O . 1 0 F M 1 0 5 . 7 0 M H z
R E T U R N N E X T E X I T
4. Up to 10 channels can be displayed at a time. If
there are more than 10 channels, press INFO
on the remote controller once more to display
the next page.
The list display will disappear automatically in 5
seconds.
TUNER OPERATION (PRESET MEMORY)
PRESET MEMORY
With this unit you can preset up to 60 FM/AM stations
in any order.
For each station, you can memorize the frequency
and reception mode if desired.
AUTO PRESET MEMORY
This function automatically scans the FM and AM
band and enters all stations with proper signal
strength into the memory.
2. 4. 1. 3. 5. 2.
1. To select FM , press the BAND button on the
front panel.
2. While pressing the MEMORY button, press the
2 cursor button.
“AUTO PRESET” will appear on the display,
and scanning starts from the lowest frequency.
3. Each time the tuner fi nds a station, scanning
will pause and the station will be played for fi ve
seconds.
During this time, the following operations are
possible.
The band can be changed by the BAND button.
4. If no button is pressed during this period, the
current station is memorized in location Preset
01.
If you wish to skip the current station, press the
3 cursor button during this period, this station
is skipped and auto presetting continues.
5. Operation stops automatically when all 60
preset memory positions are fi lled or when
auto scanning attains the highest end of all
bands. If you desire to stop the auto preset
memory at anytime, press the CLEAR button.
MANUAL PRESET MEMORY
2.
3.
3. 2. 4.
(Using the unit)
1. Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2. Press the MEMORY button on the front panel.
“– –“ (preset number) starts blinking on the
display.
3. Select the preset number by pressing the 1
or 2 cursor buttons, while this is still blinking
(approx. 5 seconds)
4. Press the MEMORY button again to enter. The
display stops blinking.
The station is now stored in the specifi ed preset
memory location.
(Using the remote controller)
1. Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2. Press the MEMO button on the remote
controller. “– –“ (preset number) starts blinking
on the display.
3. Enter the desired preset number by pressing
the numeric buttons.
Note:
• When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a few
seconds.
RECALLING A PRESET STATION
3. 1.
2.
2.
(Using the unit)
1. Select the desired preset station by pressing
the 1 or 2 cursor buttons on the front panel.
(Using the remote controller)
1. Press the TUNE button twice within two
seconds on the remote controller.
2. Press the 1 or 2 button to tune in the deseired
preset station.
Or enter the preset station number with the
numeric buttons.
PRESET SCAN
1.
5.
4.
2.
5.
(Using the remote controller)
1. Press the TUNE button twice within two
seconds on the remote controller.
2. Press the P.SCAN button on the remote
controller.
“PRESET SCAN” appears on the front display
and then the preset station with the lowest
preset number is recalled fi rst.
3. Preset stations are recalled in sequence (No.1
→ No.2 → etc.) for 10 seconds each.
No stored preset number will be skipped.