Niles Audio A4.6Ci - Manual (Page 54)

54
PROGRAMMING OVERVIEW
SOURCE
8
CASCADE OUTPUT
❏ YES ❏ NO
1
3
4
2
SOURCE DESTINATION
SOURCE
9
ZONE OUTPUT
❏ RCA ❏ DB-25
1
3
4
2
ZONE AMPLIFIER
5
6
SETTING
FIXED / VARIABLE
❏ ❏
❏ ❏
❏ ❏
❏ ❏
❏ ❏
❏ ❏
/
/
/
/
/
/
MASTER KEYPAD MODULE
( CHOOSE ONE )
❏ SOLO ❏ SELECT
❏ INPUT EXPANDER
OPTIONAL ACCESSORY
MODULES
❏ NUMERIC
❏ TRANSPORT
❏ IR SENSOR
ZONE #
ZONE NAME
MASTER KEYPAD MODULE
( CHOOSE ONE )
❏ SOLO ❏ SELECT
❏ INPUT EXPANDER
OPTIONAL ACCESSORY
MODULES
❏ NUMERIC
❏ TRANSPORT
❏ IR SENSOR
ZONE NAME
MASTER KEYPAD MODULE
( CHOOSE ONE )
❏ SOLO ❏ SELECT
❏ INPUT EXPANDER
OPTIONAL ACCESSORY
MODULES
❏ NUMERIC
❏ TRANSPORT
❏ IR SENSOR
ZONE NAME
❏ SOLO ❏ SELECT
❏ INPUT EXPANDER
OPTIONAL ACCESSORY
MODULES
❏ TRANSPORT
❏ IR SENSOR
ZONE NAME
❏ SOLO ❏ SELECT
❏ INPUT EXPANDER
OPTIONAL ACCESSORY
MODULES
❏ NUMERIC
❏ TRANSPORT
❏ IR SENSOR
ZONE NAME
❏ SOLO ❏ SELECT
❏ INPUT EXPANDER
OPTIONAL ACCESSORY
MODULES
❏ NUMERIC
❏ TRANSPORT
❏ IR SENSOR
ZONE NAME
❏ NUMERIC
FROM EXPANDER # FROM EXPANDER # FROM EXPANDER # FROM EXPANDER # FROM EXPANDER # FROM EXPANDER #
10
MASTER KEYPAD MODULE
( CHOOSE ONE )
MASTER KEYPAD MODULE
( CHOOSE ONE )
MASTER KEYPAD MODULE
( CHOOSE ONE )
ZONE SETUP
1 ZONE # 2 ZONE # 3 ZONE # 4 ZONE # 5 ZONE # 6
This documents the audio output from the shared source components
going to the next Slave or the Home Theater.
• Does your system include other preamps or a Home Theater?
(YES/NO)
• If yes, specify where the cascade output is going (for example, a
Home Theater or the next Slave preamp in the system).
To ensure accuracy, check the information in this box against the
information documented under Cascade Input (box #4 for the Slave
Schematic sheet).
Also note that the Home Theater is always the last to receive the
shared audio signals in multi-zone systems.
• Indicate if using either RCA or DB-25 to connect
to the amplifiers
• Then list the brand and model of the amplifier
receiving the output.
Keypad Input Information:
• Check if a Master Key Module was installed (Solo ™ /Select ™ ) or if zone has an expander. (Expanded zones have more than one
keypad or more than one room.)
• Indicate any optional accessory module used (Numeric ™ , Transport, ™ or IR sensor).
• Identify the zones according to the numbers that correspond to each Slave preamp (Slave 1: Zones 7-12; Slave 2: Zones 13-18;
Slave 3: Zones 19-24).
• Zone Name
• If a zone has an expander, indicate its number. The expander should be numbered the same as the zone to which it is connected,
since each zone has a unique number. (For example, Zone 16 would have Expander #16.)
For zones that require more than three keypads, install two expanders. These become "A and B." (For example, two expanders in
Zone 16 would be Expander 16A and Expander 16B.)
Note: After you have completed each necessary Slave Schematic sheet, complete any additional Expander Schematic sheet
your system requires for individual keypad documentation.