Rockwell Automation 1608M MegaDySC User Manual, 400 A Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for 1608M MegaDySC User Manual, 400 A Rockwell Automation
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 48 |
| Size: | 2.43 MB |
Show table of contents
Document Outline
- Important User Information
- Additional Resources
- Chapter 1
- Chapter 2
- Installation
- System Components
- System Layout
- System Clearance
- System Mounting
- Electrical Interconnections
- Instructions for energizing loads before commissioning
- Figure 5 - Rear view of Automatic Bypass Switch board
- 1. Route the INPUT power cables (labeled L1, L2, L3) through the top bushing in the right-side wall of the switchboard, labeled “Input to DySC”
- 2. Route the OUTPUT power cables (X1, X2, X3) and Ground cable through the bottom bushing labeled “Output from DySC”
- 3. Route the control cable harness from the lower front switchboard pan into the MegaDySC section through the matching holes in the lower front side panels. Install the 3.5” snap-in grommet so that it protrudes into the MegaDySC cabinet before rout...
- 4. Lockout circuit breakers CBI and CBO in the Automatic Bypass Switchboard.
- 5. Install utility input and load output conductors.
- 6. Energize the switchboard. The MegaDySC touch screen display will be active only if the control harness has been plugged in on the MegaDySC side. If the screen is active then 120VAC is present at several points within the MegaDySC enclosure.
- 7. Push the green CLOSE CBB button to energize loads. The remaining interconnections and commissioning must be completed by factory-trained technicians.
- MegaDySC System Installation Connections Checklist
- MegaDySC System Interconnections Checklist
- Instructions for energizing loads before commissioning
- Installation
- Chapter 3
- Chapter 4
- Chapter 5
- Operation
- System Description
- MegaDySC Operation
- Automatic Bypass Switchboard Operation
- Automatic Bypass Switchboard Operating Instructions
- Automatic System
- Manual Transfer to Maintenance Bypass (Bypass Mode)
- 1. If CBB is tripped, Press both "CBB RESET" pushbuttons.
- 2. Press green "CLOSE CBB" pushbutton.
- 3. Confirm that red "BYPASS CLOSED" lamp is lit.
- 4. Press red "OPEN/RESET CBI" pushbutton. Output breaker (CBO) will open automatically.
- 5. Confirm that both CBI and CBO are open.
- 6. The MegaDySC is now bypassed and isolated for maintenance.
- Manual Transfer to MegaDySC (Normal Mode)
- 1. Press red "OPEN/RESET CBI" pushbutton then press green "CLOSE CBI" pushbutton. Note: "CLOSE CBI" is inhibited for one minute after power cycling.
- 2. Confirm that the MegaDySC screen is lit, is green and displays "OK" in the upper-left corner.
- 3. Close CBO by manually moving the handle to the "OFF" (0) position and then to the “ON” (|) position.
- 4. Confirm that the screen on the MegaDySC displays "OK".
- 5. Press red “OPEN CBB” pushbutton
- 6. The MegaDySC system is now providing power to the load.
- Transient Voltage Surge Suppression
- Troubleshooting Notes
- Operation
- Chapter 6
- Chapter 7
- Chapter 8
- Specifications
- Table 13 - Technical Specifications 400 A MegaDySC
- Table 14 - MegaDySC Heat Loading and Typical Efficiency
- 480V
- 480V
- 380V
- 380V
- SR
- ER
- SR
- ER
- 2421
- 2852
- 2321
- 2624
- 8270
- 9740
- 7925
- 8960
- > 99%
- > 99%
- > 99%
- > 99%
- 3W
- 3W
- 4W
- 4W
- SR
- ER
- SR
- ER
- 1792 lb [813 kg]
- 2656 lb [1205 kg]
- 1792 lb [813 kg]
- 2656 lb [1205 kg]
- 1075 lb [488 kg]
- 1075 lb [488 kg]
- 1039 lb [471 kg]
- 1039 lb [471 kg]
- 2867 lb [1300kg]
- 3731 lb [1692 kg]
- 2831 lb [1284 kg]
- 3695 lb [1676 kg]
- Specifications