Dell OptiPlex 3010 (Mid 2012) Instruction Manuals and User Guides
We have 3 Instruction Manuals and User Guides for OptiPlex 3010 (Mid 2012) Dell
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 61 |
| Size: | 16.77 MB |
Show table of contents
Document Outline
- Dell OptiPlex 3010 Mini-Tower Owner's Manual
- Working on Your Computer
- Removing and Installing Components
- Removing the Cover
- Installing the Cover
- Removing the Front Bezel
- Installing The Front Bezel
- Removing the Expansion Card
- Installing The Expansion Card
- Removing the Optical Drive
- Installing The Optical Drive
- Removing the Hard Drive
- Installing The Hard Drive
- Removing the Memory
- Installing the Memory
- Removing The Chassis Intrusion Switch
- Installing the Intrusion Switch
- Removing The Speaker
- Installing the Speaker
- Removing the Heat Sink and Processor
- Installing the Heat Sink and Processor
- Removing The Coin-Cell Battery
- Installing The Coin-Cell Battery
- Removing the Power-Switch Cable
- Installing the Power-Switch Cable
- Removing the Front Thermal Sensor
- Installing the Front Thermal Sensor
- Removing The System Fan
- Installing the System Fan
- Removing the Input/Output Panel
- Installing the Input/Output Panel
- Removing The Power Supply
- Installing the Power Supply
- Removing The System Board
- Installing The System Board
- System Setup
- Troubleshooting
- Diagnostic LEDs
- Beep Codes
- Error Messages
- Address mark not found
- Alert! Previous attempts at booting this system have failed at checkpoint [nnnn]. For help in resolving this problem, please note this checkpoint and contact Dell Technical Support.
- Alert! Security override Jumper is installed.
- Attachment failed to respond
- Bad command or file name
- Bad error-correction code (ECC) on disk read
- Controller has failed
- Data error
- Decreasing available memory
- Diskette drive 0 seek failure
- Diskette read failure
- Diskette subsystem reset failed
- Gate A20 failure
- General failure
- Hard-disk drive configuration error
- Hard-disk drive controller failure
- Hard-disk drive failure
- Hard-disk drive read failure
- Invalid configuration information-please run SETUP program
- Invalid Memory configuration, please populate DIMM1
- Keyboard failure
- Memory address line failure at address, read value expecting value
- Memory allocation error
- Memory data line failure at address, read value expecting value
- Memory double word logic failure at address, read value expecting value
- Memory odd/even logic failure at address, read value expecting value
- Memory write/read failure at address, read value expecting value
- Memory size in CMOS invalid
- Memory tests terminated by keystroke
- No boot device available
- No boot sector on hard-disk drive
- No timer tick interrupt
- Non-system disk or disk error
- Not a boot diskette
- Plug and play configuration error
- Read fault
- Requested sector not found
- Reset failed
- Sector not found
- Seek error
- Shutdown failure
- Time-of-day clock stopped
- Time-of-day not set-please run the System Setup program
- Timer chip counter 2 failed
- Unexpected interrupt in protected mode
- WARNING: Dell's Disk Monitoring System has detected that drive [0/1] on the [primary/secondary] EIDE controller is operating outside of normal specifications. It is advisable to immediately back up your data and replace your hard drive by calling your support desk or Dell.
- Write fault
- Write fault on selected drive
- X:\ is not accessible. The device is not ready
- Specifications
- Contacting Dell
| Recognized languages: | English |
|---|---|
| Pages: | 9 |
| Size: | 1.39 MB |
Show table of contents
| Recognized languages: | English |
|---|---|
| Pages: | 63 |
| Size: | 18.80 MB |
Show table of contents
Document Outline
- Dell OptiPlex 3010 Desktop Owner's Manual
- Working on Your Computer
- Removing and Installing Components
- Removing the Cover
- Installing The Cover
- Removing the Front Bezel
- Installing The Front Bezel
- Removing the Expansion Card
- Installing The Expansion Card
- Removing the Optical Drive
- Installing The Optical Drive
- Removing the Hard Drive
- Installing The Hard Drive
- Removing the Memory
- Installing The Memory
- Removing the Chassis Intrusion Switch
- Installing The Chassis Intrusion Switch
- Removing The Speaker
- Installing The Speaker
- Removing The Heat Sink and Processor
- Installing The Heat Sink and Processor
- Removing The Coin-Cell Battery
- Installing The Coin-Cell Battery
- Removing The Power-Switch Cable
- Installing The Power-Switch Cable
- Removing The Front Thermal Sensor
- Installing The Front Thermal Sensor
- Removing The System Fan
- Installing The System Fan
- Removing The Input/Output Panel
- Installing The Input/Output Panel
- Removing The Power Supply
- Installing The Power Supply
- Removing the System Board
- Installing the System Board
- Removing The PSU Thermal Sensor
- Installing The PSU Thermal Sensor
- System Setup
- Troubleshooting
- Diagnostic LEDs
- Beep Codes
- Error Messages
- Address mark not found
- Alert! Previous attempts at booting this system have failed at checkpoint [nnnn]. For help in resolving this problem, please note this checkpoint and contact Dell Technical Support.
- Alert! Security override Jumper is installed.
- Attachment failed to respond
- Bad command or file name
- Bad error-correction code (ECC) on disk read
- Controller has failed
- Data error
- Decreasing available memory
- Diskette drive 0 seek failure
- Diskette read failure
- Diskette subsystem reset failed
- Gate A20 failure
- General failure
- Hard-disk drive configuration error
- Hard-disk drive controller failure
- Hard-disk drive failure
- Hard-disk drive read failure
- Invalid configuration information-please run SETUP program
- Invalid Memory configuration, please populate DIMM1
- Keyboard failure
- Memory address line failure at address, read value expecting value
- Memory allocation error
- Memory data line failure at address, read value expecting value
- Memory double word logic failure at address, read value expecting value
- Memory odd/even logic failure at address, read value expecting value
- Memory write/read failure at address, read value expecting value
- Memory size in CMOS invalid
- Memory tests terminated by keystroke
- No boot device available
- No boot sector on hard-disk drive
- No timer tick interrupt
- Non-system disk or disk error
- Not a boot diskette
- Plug and play configuration error
- Read fault
- Requested sector not found
- Reset failed
- Sector not found
- Seek error
- Shutdown failure
- Time-of-day clock stopped
- Time-of-day not set-please run the System Setup program
- Timer chip counter 2 failed
- Unexpected interrupt in protected mode
- WARNING: Dell's Disk Monitoring System has detected that drive [0/1] on the [primary/secondary] EIDE controller is operating outside of normal specifications. It is advisable to immediately back up your data and replace your hard drive by calling your support desk or Dell.
- Write fault
- Write fault on selected drive
- X:\ is not accessible. The device is not ready
- Specifications
- Contacting Dell