American Dryer Corp. AD-385 Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for AD-385 American Dryer Corp.
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 68 |
| Size: | 314 KB |
Show table of contents
Document Outline
- “IMPORTANTNOTE TO PURCHASER”
- IMPORTANT
- CAUTION
- WARNING
- FOR YOUR SAFETY
- WARNING
- WARNING
- WARNING
- IMPORTANT
- SECTION II
- A. LOCATION REQUIREMENTS
- B. UNPACKING/SETTING UP
- D. FRESH AIR SUPPLY
- IMPORTANT: The dryer and its individual shut-off valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa).
- NOTE: The dryer must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure test of the gas supply system at test pressures equal to or less than 1/2 psig (3.5 kPa).
- H. PREPARATION FOR OPERATION/START-UP
- IMPORTANT: If the blower wheel (impellor/fan) is rotating in the wrong
- direction, this will not only drastically reduce drying efficiency, but it can also cause premature component failure.
- T. PREOPERATIONAL INSTRUCTIONS COINMODELS
- K. SHUT DOWN INSTRUCTIONS
- SECTION IV
- SECTION V
- A. RETURNING WARRANTY CARPrS^
- B. WARRANTY
- C. RETURNING WARRANTY PARTS
- A. CLEANING
- NOTE: The frequency of cleaning the lint screen can best be determined from experience at each location.
- WARNING: TO AVOID THE HAZARD OF ELECTRICAL SHOCK,
- DISCONTINUE ELECTRICAL SUPPLY TO THE DRYER.
- B. ADTUSTMENTS
- C. LUBRICATION
- Microprocessor (Coin') Models
- F. The dryer does not start, and the microprocessor controller (computer) LED display shows
- G. Microprocessor controller (computer) display reads "dSFL"...
- H. Microprocessor controller (computer) will not accept any, or only accept certain keyboard entries...
- I. Microprocessor controller (computer) locks up and a LED display reads erroneous message(s) or only partial segments...
- J. Dryer stops during a cycle and microprocessor controller (computer) LED display returns to "FILL"...
- N. Condensation on main door glass...
- O. Dryer or scraping noise at basket (tumbler) area...
- A. Dryer will not start...indicator light is off...
- B. Drive motor not operating (does not start)... Indicator light is on ...
- C. Drive motor operates okay for a few minutes, and then stops and will not restart..
- D. Heating unit is not operating (no heat) ...no voltage at heating unit (i.e., DSI module)
- E. No heat...voltage is confirmed at heating unit (i.e., DSI module)...
- I. Dryer or scraping noise at basket (tumbler) area...
- J. Excessive noise and/or vibration...
- COPU Microprocessor ('Computer') Models
- A. No display (microprocessor [computer] models ONLY)...
- B. Drive motor not operating (does not start)...
- C. Drive motor operates okay for a few minutes, and then stops and will not restart...
- D. Drive motor runs for a few minutes and stops... microprocessor controller (computer)
- E. Microprocessor controller (computer) display reads "dSFL" continuously and the buzzer (tone) sounds every 30-seconds...
- F. Microprocessor controller (computer) display reads "dOOr" and microprocessor controller (computer) "dOOr" LED indicator is off...
- G. Microprocessor controller (computer) LED display reads "dOOr" and microprocessor controller (computer) "dOOr" LED indicator is on...
- I. Microprocessor controller (computer) will only accept certain keyboard (touchpad) entries...
- J. Microprocessor controller (computer) locks up and display reads erroneous message(s) or only partial segments...
- L. Dryer stops during a cycle, microprocessor controller (computer) buzzer (tone) sounds for 5-seconds, and then the LED display returns to "FILL"...
- M. Microprocessor controller (computer) LED display reads "SEFL"...
- N. Microprocessor controller (computer) LED display reads "Hot"...
- Q. No heat...voltage is confirmed at heating unit (i.e., DSI module,)...
- R. Dryer is taking too long to dry...
- S. At completion of the "AUtO" drying/cooling cycle...load is coming over dried...
- T. At completion of the "AUtO" drying/cooling cycle...load is coming damp...
- U. Main burners are burning with a yellow flame (for Gas Models ONLY)...
- V. Condensation on main door glass...
- W. Dryer or scraping noise at basket (tumbler) area...
- AA. Excessive noise and/or vibration...
- TIMER MODELS
- A. Dryer will not start...drive motor is not operating (indicator light is off)...
- B. Drive motor not operating (does not start)... Indicator light is on ...
- C. Drive motor operates okay for a few minutes, and then stops and will not restart.,
- D. Heating unit is not operating (no heat)...no voltage at heating unit (i.e., DSI module)
- E. No heat...voltage is confirmed at heating unit (i.e., DSI module)...
- F. Dryer operates but is taking too long to dry...
- I. Dryer or scraping noise at basket (tumbler) area...
- J. Excessive noise and/or vibration...
- SECTION VIII