American Dryer Corp. AD-385 User Manual
American Dryer Corp. Dryers
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

WARNING: For your safety the
information in this manual must be
followed to minimize the risk of fire or
explosion or to prevent property damage,
personal injury or death.
-Do not store or use gasoline or other flammable
vapor and liquids in the vicinity of this or any
other appliance.
■WHAT DO YOU DO IF YOU SMELL GAS
* Do not try to light any appliance.
* Do not touch any electrical switch; do not use
any phone in your building.
* Clear the room, building or area of all
occupants.
* Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
* If you cannot reach your gas supplier, call the
fire department.
- Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
JOC
American Dryer Corp.
AVERTISSEMENT : Assurez-vous de bien
suivre les instructions données dans cette
notice poiff réduire au minimiim le risque
d’incendie ou d’explosion ou pour éviter tout
dommage matériel, toute blessure ou la mort.
■Ne pas entreposer ni utiliser d’essence ni
d’autres vapeurs ou liquides inflammables dans
le voisinage de cet appareil ou de tout autre
appareil.
■ QUE FAIRE SI VOUS SENTEZ UNE ODEUR
DE GAZ:
* Ne pas tenter d’allumer d’appareil.
* Ne touchez à aucun interrupteur. Ne pas
vous servir des téléphones se trouvant dans
le bâtiment où vous vous trouvez..
* Évacuez la pièce, le bâtiment ou la zone.
* Appelez immédiatement votre fournisseur de
gaz depuis un voisin. Suivez les instructions
du fournisseur.
* Si vous ne pouvez rej oindre le fournisseur
de gaz, appelez le service des incendies.
- L’installation et l’entretien doivent être assurés
par un installateur ou un service d’entretien
qualifié ou par le fournisseur de gaz.
For replacement parts, contact the distributor from which the dryer
was purchased or
^
American Dryer Corporation
88 Currant Road
FaU River MA 02720-4781
Telephone: (508)678-9000 / Fax: (508)678-9447
E-mail: [email protected]
111298SL/abe
ADC Part No. 112188
Document Outline
- “IMPORTANTNOTE TO PURCHASER”
- IMPORTANT
- CAUTION
- WARNING
- FOR YOUR SAFETY
- WARNING
- WARNING
- WARNING
- IMPORTANT
- SECTION II
- A. LOCATION REQUIREMENTS
- B. UNPACKING/SETTING UP
- D. FRESH AIR SUPPLY
- IMPORTANT: The dryer and its individual shut-off valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa).
- NOTE: The dryer must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure test of the gas supply system at test pressures equal to or less than 1/2 psig (3.5 kPa).
- H. PREPARATION FOR OPERATION/START-UP
- IMPORTANT: If the blower wheel (impellor/fan) is rotating in the wrong
- direction, this will not only drastically reduce drying efficiency, but it can also cause premature component failure.
- T. PREOPERATIONAL INSTRUCTIONS COINMODELS
- K. SHUT DOWN INSTRUCTIONS
- SECTION IV
- SECTION V
- A. RETURNING WARRANTY CARPrS^
- B. WARRANTY
- C. RETURNING WARRANTY PARTS
- A. CLEANING
- NOTE: The frequency of cleaning the lint screen can best be determined from experience at each location.
- WARNING: TO AVOID THE HAZARD OF ELECTRICAL SHOCK,
- DISCONTINUE ELECTRICAL SUPPLY TO THE DRYER.
- B. ADTUSTMENTS
- C. LUBRICATION
- Microprocessor (Coin') Models
- F. The dryer does not start, and the microprocessor controller (computer) LED display shows
- G. Microprocessor controller (computer) display reads "dSFL"...
- H. Microprocessor controller (computer) will not accept any, or only accept certain keyboard entries...
- I. Microprocessor controller (computer) locks up and a LED display reads erroneous message(s) or only partial segments...
- J. Dryer stops during a cycle and microprocessor controller (computer) LED display returns to "FILL"...
- N. Condensation on main door glass...
- O. Dryer or scraping noise at basket (tumbler) area...
- A. Dryer will not start...indicator light is off...
- B. Drive motor not operating (does not start)... Indicator light is on ...
- C. Drive motor operates okay for a few minutes, and then stops and will not restart..
- D. Heating unit is not operating (no heat) ...no voltage at heating unit (i.e., DSI module)
- E. No heat...voltage is confirmed at heating unit (i.e., DSI module)...
- I. Dryer or scraping noise at basket (tumbler) area...
- J. Excessive noise and/or vibration...
- COPU Microprocessor ('Computer') Models
- A. No display (microprocessor [computer] models ONLY)...
- B. Drive motor not operating (does not start)...
- C. Drive motor operates okay for a few minutes, and then stops and will not restart...
- D. Drive motor runs for a few minutes and stops... microprocessor controller (computer)
- E. Microprocessor controller (computer) display reads "dSFL" continuously and the buzzer (tone) sounds every 30-seconds...
- F. Microprocessor controller (computer) display reads "dOOr" and microprocessor controller (computer) "dOOr" LED indicator is off...
- G. Microprocessor controller (computer) LED display reads "dOOr" and microprocessor controller (computer) "dOOr" LED indicator is on...
- I. Microprocessor controller (computer) will only accept certain keyboard (touchpad) entries...
- J. Microprocessor controller (computer) locks up and display reads erroneous message(s) or only partial segments...
- L. Dryer stops during a cycle, microprocessor controller (computer) buzzer (tone) sounds for 5-seconds, and then the LED display returns to "FILL"...
- M. Microprocessor controller (computer) LED display reads "SEFL"...
- N. Microprocessor controller (computer) LED display reads "Hot"...
- Q. No heat...voltage is confirmed at heating unit (i.e., DSI module,)...
- R. Dryer is taking too long to dry...
- S. At completion of the "AUtO" drying/cooling cycle...load is coming over dried...
- T. At completion of the "AUtO" drying/cooling cycle...load is coming damp...
- U. Main burners are burning with a yellow flame (for Gas Models ONLY)...
- V. Condensation on main door glass...
- W. Dryer or scraping noise at basket (tumbler) area...
- AA. Excessive noise and/or vibration...
- TIMER MODELS
- A. Dryer will not start...drive motor is not operating (indicator light is off)...
- B. Drive motor not operating (does not start)... Indicator light is on ...
- C. Drive motor operates okay for a few minutes, and then stops and will not restart.,
- D. Heating unit is not operating (no heat)...no voltage at heating unit (i.e., DSI module)
- E. No heat...voltage is confirmed at heating unit (i.e., DSI module)...
- F. Dryer operates but is taking too long to dry...
- I. Dryer or scraping noise at basket (tumbler) area...
- J. Excessive noise and/or vibration...
- SECTION VIII