Honeywell SC1000 User Manual
Sc instrumentation
Table of contents
Document Outline
- SC Instrumentation
- Contents
- Contents 3
- Chapter 1 Introduction 9
- Chapter 2 Getting Started Quickly 15
- Chapter 3 Operating Modes 19
- Chapter 4 Chassis Models 25
- Chapter 5 System Connector 35
- Chapter 6 System Menu 41
- Chapter 7 Serial Communications 47
- Chapter 8 Display Menu 51
- Chapter 9 Limits 53
- Chapter 10 Strain-Gage Input Channel 59
- Chapter 11 AC/AC-LVDT Input Channel 79
- Chapter 12 High-Level Input Channel 97
- Chapter 13 Relay Output Channel 123
- Chapter 14 DAC Output Channel 129
- Chapter 15 Split Display Virtual Channel 139
- Chapter 16 Mathematics Virtual Channel 143
- Chapter 17 Error Messages 151
- Chapter 18 Setup Menu Reference 157
- Index 169
- Warranty 173
- Chapter 1 Introduction
- Chapter 2 Getting Started Quickly
- Chapter 3 Operating Modes
- Chapter 4 Chassis Models
- Chapter 5 System Connector
- Chapter 6 System Menu
- Chapter 7 Serial Communications
- Chapter 8 Display Menu
- Chapter 9 Limits
- Chapter 10 Strain-Gage Input Channel
- 10.1 Features
- 10.2 Wiring
- 10.3 Calibration Procedure
- 10.4 Specifications
- 10.5 Channel Menu
- 10.6 Analog Output Configuration
- 10.7 Troubleshooting
- Chapter 11 AC/AC-LVDT Input Channel
- 11.1 Features
- 11.2 Wiring
- 11.3 Calibration Procedure
- 11.4 Specifications
- 11.5 Channel Menu
- 11.6 Electrical Null and Transducer Mounting
- 11.7 Analog Output Configuration
- 11.8 Troubleshooting
- Chapter 12 High-Level Input Channel
- 12.1 Features
- 12.2 Wiring
- 12.2.1 Channel Connector
- 12.2.2 Bi-polar Voltage Amplifiers
- 12.2.3 “3-wire Voltage” Amplifiers
- 12.2.4 “3-wire Voltage” Amplifiers with Single-wire Shunt Cal
- 12.2.5 “3-wire Current” Amplifiers
- 12.2.6 “2-wire Current” Amplifiers with Buffered Shunt Cal
- 12.2.7 “2-wire Current” Amplifiers with Single- wire Shunt Cal
- 12.2.8 Low Voltage DC-DC LVDTs
- 12.3 Excitation and Signal Jumpers
- 12.4 Calibration Procedure
- 12.5 Specifications
- 12.6 Channel Menu
- 12.7 Analog Output Configuration
- 12.8 Troubleshooting
- Chapter 13 Relay Output Channel
- Chapter 14 DAC Output Channel
- Chapter 15 Split Display Virtual Channel
- Chapter 16 Mathematics Virtual Channel
- Chapter 17 Error Messages
- 17.1 Overview
- 17.2 Error Message List
- Error 05, DIVIDE BY ZERO
- Error 07, SQUARE ROOT
- Error 09, LOG/LN
- Error 16, +15V SUPPLY HIGH
- Error 17, +15V SUPPLY LOW
- Error 18, -15V SUPPLY HIGH
- Error 19, -15V SUPPLY LOW
- Error 20, CHANNEL >MAXCH
- Error 21, BLOWN STACK
- Error 22, TYPE NOT FOUND
- Error 23, CAN'T RENDER FS
- Error 24, SIG.MOD CRC ROM
- Error 25, SIG.MOD CRC READ
- Error 26, NO SIG.MOD.
- Error 27, S.EE WRITE NAK
- Error 28, S.EE READ NAK
- Error 29, S.EE VERIFY FAIL
- Error 30, S.EE ERASE NAK
- Error 31, BLANK IDENT
- Error 32, BOGUS EE ADDR
- Error 33, SIG.MOD WIRES
- Error 34, SIG.MOD MISMATCH
- Error 35, BOGUS MENU TYPE
- Error 36, BAD EE TABLE
- Error 37, BAD PERSONALITY
- Error 38, BAD FORMAT
- Error 39, WRONG HARDWARE
- Error 41, SHUNT CAL ERROR
- Error 43, BAD IDENT CRC
- Error 44, BAD FUNCTION
- Error 45, A/D NAK
- Error 46, SENSE WIRES
- Error 47, BAD EE TYPE REQ
- Error 48, NULL MENU
- Error 49, NULL ACTION FCN
- Error 50, EXCITATION
- Error 51, CAN'T DO EXC.
- Error 52, SIG.MOD LENGTH R
- Error 53, SIG.MOD RECTYPE
- Error 54, SIG.MOD LENGTH W
- Error 55, SIG.MOD VERIFY SP
- Error 56, SIG.MOD VERIFY
- Error 57, WRONG SIG.MOD.
- Error 58, WRONG EE VERSION
- Error 59, CAN’T DO SIG.MOD
- Error 60, SLAVE TIMEOUT
- Error 61, LOAD NOT GT LOAD
- Error 62, SLAVE NAK
- Error 67, LOADS NOT CLOSE
- Error 68, CAN'T CALIBRATE
- Error 70, CAN'T DO GAIN
- Error 71, SLAVE CHECKSUM
- Error 72, CAN'T DO FILTER
- Error 73, SLAVE NOT INIT
- Error 74, SLAVE BAD REPLY
- Error 75, SLAVE NOT FOUND
- Error 81, OPERAND EXPECTED
- Error 82, BAD OPERAND
- Error 83, BAD INSTRUCTION
- Error 84, BAD VALUE
- Error 85, UNREACHABLE GOTO
- Error 87, GOTO NOT JUMP
- Chapter 18 Setup Menu Reference
- Index
- Warranty