Roland V-1200HD Multi-Format Video Switcher - Manual (Page 30)

30
Other Features
Saving/Recalling Settings
This saves the following settings together in a single file to a USB
flash drive connected to the USB port. You can then recall the saved
file from the USB flash drive to the V-1200HD for use when needed.
 Settings Saved on the USB Flash Drive
The settings saved in MEMORY 1 through 8 in V-1200HD RCS or on
the V-1200HDR are saved to the USB flash drive.
* The current settings are not saved.
Saving a New Settings File (Save As)
1.
Press the [MENU] button  select “Backup”  “Save As,”
then press the [ENTER] button.
2.
Specify the file name, select “SAVE,” then press the
[ENTER] button.
The extension of the file name is [V12].
3.
The message “Push ENTER to execute.” appears. To
execute the operation, press the [ENTER] button.
(If you want to cancel the operation, press the [MENU] button.)
The new settings file is saved on the USB flash drive.
Saving Settings by Overwriting
1.
Press the [MENU] button  select “Backup”  “Save” then
press the [ENTER] button.
2.
Select the file to overwrite, then press the [ENTER] button.
3.
The message “Push ENTER to execute.” appears. To
execute the operation, press the [ENTER] button.
(If you want to cancel the operation, press the [MENU] button.)
The settings are saved on the USB flash drive, overwriting the older
file.
Deleting Settings
1.
Press the [MENU] button  select “Backup”  “Delete”
then press the [ENTER] button.
2.
Select the file to delete, then press the [ENTER] button.
3.
The message “Push ENTER to execute.” appears. To
execute the operation, press the [ENTER] button.
(If you want to cancel the operation, press the [MENU] button.)
The settings are deleted from the USB flash drive.
Recalling Settings
This recalls the settings for MEMORY 1 through 8 saved on a USB
flash drive. Recalling the settings overwrites any values currently in
MEMORY 1 through 8.
* The current settings remain when the settings for MEMORY 1
through 8 are recalled.
1.
Press the [MENU] button  “Restore” then press the
[ENTER] button.
2.
Select the file to load, then press the [ENTER] button.
3.
The message “Push ENTER to execute.” appears. To
execute the operation, press the [ENTER] button.
(If you want to cancel the operation, press the [MENU] button.)
The settings are recalled.
Checking the Version Information
This displays the program version information for the V-1200HD
itself (MAIN) and for expansion interfaces (EXP A and EXP B)
connected at expansion slots A and B.
1.
Press the [MENU] button and select “System,” then press
the [ENTER] button.
The program version information is displayed.
* When no expansion interfaces are inserted into expansion slots A
and B, no version information is displayed at “EXP A” and “EXP B.”
Formatting a USB Flash Drive
To use a USB flash drive with the V-1200HD, it must first be
formatted with the unit.
NOTE
5 The V-1200HD does not recognize unformatted USB flash drives.
5 Performing formatting causes all data already saved on the USB
flash drive to be deleted. If the flash drive contains necessary
data, back it up onto a computer or elsewhere before formatting
the drive.
1.
Connect the USB flash drive to the USB port on the front
panel.
2.
Press the [MENU] button and select “Format,” then press
the [ENTER] button.
3.
The message “Push ENTER to execute.” appears. To
execute the operation, press the [ENTER] button.
(If you want to cancel the operation, press the [MENU] button.)
Formatting of the USB flash drive is carried out.
NOTE
5 When turning off the power to the V-1200HD, first remove the
USB flash drive from the USB port before you turn off the power.
If the power is turned off while a flash drive remains connected
to the V-1200HD, the V-1200HD might fail to start correctly at
the next powerup.
5 Connect the flash drive to the USB port located on the front
panel. (No operation takes place if the drive is connected to the
USB port on the rear panel.)
5 Carefully insert the USB flash drive all the way in–until it is firmly
in place.
5 Never turn off the power or disconnect the USB flash drives
when the access lamp of USB flash drives are lit or blinking
5 After connecting the USB flash drive, a short wait may be
required until reading and writing data is possible.
Returning Settings to the Factory-Default
State (Factory Reset)
This returns values that have been set to their factory defaults.
If operation that differs from what is described in the owner’s
manual occurs even when the steps are followed correctly, try
performing a factory reset.
NOTE
Executing a factory reset causes all settings made up to then to
be lost.
1.
Press the [MENU] button and select “Factory Reset,” then
press the [ENTER] button.
2.
The message “Push ENTER to execute.” appears. To
execute the operation, press the [ENTER] button.
(If you want to cancel the operation, press the [MENU] button.)
A factory reset is executed.