Ericsson Multi-Format Receiver RX1290 User Manual
Rx1290 multi-format receiver, Software version 3.0.0 (and later), Reference guide
Table of contents
Document Outline
- re_e10228_00_6
- re_e10228_01_6
- re_e10228_02_6
- re_e10228_03_6
- 3 Operating the Equipment Locally
- Contents
- 3.1 Powering the Equipment
- 3.2 Front Panel Controls and Pushbuttons
- 3.3 Front Panel Operating Modes
- 3.4 Using the Local Controls
- 3.5 Setting Up Preset Services (Menu 1)
- 3.6 Setting Up the Input (Menu 2)
- 3.7 Service Configuration (Menu 3)
- 3.7.1 Selecting and Setting Up a Service
- 3.7.2 Selecting the Video Component
- 3.7.3 Setting Down Conversion Mode
- 3.7.4 Setting SD Monitor Aspect Ratio
- 3.7.5 Setting Video Delay
- 3.7.6 Setting Video Output mode
- 3.7.7 Setting Low Delay Mode – RX1290/SWO/LDELAY
- 3.7.8 Selecting the Audio Component
- 3.7.9 Setting Up Asynchronous Data (RS232)
- 3.7.10 Setting Up High Speed Data Over Ethernet – RX1290/SWO/HSETHER
- 3.7.11 Setting Up Teletext
- 3.7.12 Setting Up VITC
- 3.7.13 Setting Up Closed Captions
- 3.7.14 Setting Up ITS Insertion
- 3.7.15 Setting Up VPS
- 3.7.16 Setting Up WSS
- 3.7.17 Setting Up Video Index
- 3.7.18 Setting Up Monochrome Samples
- 3.7.19 Setting Up AMOL 1 and 2
- 3.7.20 Setting Up NTSC Pedestal Insertion
- 3.7.21 Setting Up VANC Data Insertion
- 3.7.22 Setting Up Splice Point Insertion
- 3.7.23 Setting Up Station ID Insertion
- 3.7.24 Setting Up AFD Insertion
- 3.7.25 Setting Up DVB Subtitles
- 3.7.26 Setting the PCR PID Menu
- 3.7.27 Viewing the Network ID Menu
- 3.8 Setting Up the Conditional Access/Scrambling (Menu 4)
- 3.9 Setting Up the Transport Stream Output (Menu 5)
- 3.10 Setting Up the Alarms (Menu 6)
- 3.11 Setting Up System Parameters (Menu 7)
- 3.12 Restarting the Unit
- re_e10228_04_6
- 4 Operating the Equipment Remotely
- Contents
- 4.1 Remote Control
- 4.2 Returning the Unit to Local Control Mode
- re_e10228_05_6
- re_e10228_06_6
- 6 Options
- Contents
- 6.1 Hardware Enabled Options
- 6.2 DVB-S2 Input Cards (RX1290/HWO/DVBS2 andRX1290/HWO/DVBS2/IF/CONST)
- 6.3 TTV G.703 DS3 and E3 Input Card (TT1290/HWO/G703)
- 6.4 IP Input Card (TT1290/HWO/IP)
- 6.5 100/1000BaseT Dual IP Input – RX1290/HWO/GIGE
- 6.6 Software Enabled Options
- 6.7 High Speed Data Over Ethernet (RX1290/SWO/HSETHER)
- 6.8 Dolby Digital Decoder (RX1290/SWO/AC3)
- 6.9 RAS Mode 1 and 2 Conditional Access (RX1290/SWO/RAS)
- 6.10 Director Functionality (RX1290/SWO/DIR5)
- 6.11 MPEG-2 HD 4:2:2 Decode (RX1290/SWO/MPEG-2/HD/422)
- 6.12 MPEG-4 SD Decode (RX1290/SWO/MPEG4/SD)
- 6.13 MPEG-4 HD, SD MPEG-2, HD 4:2:2 Decode (RX1290/SWO/MPEG-4/HD)
- 6.14 DVB-S2 QPSK (RX1290/SWO/DVBS2/QPSK)
- 6.15 DVB-S2 QPSK and 8PSK (RX1290/SWO/DVBS2/8PSK)
- 6.16 DVB-S2 Low Symbol Rate (RX1290/SWO/DVBS2/LSym)
- 6.17 ProMPEG FEC (RX1290/SWO/IP/PROMPEG)
- 6.18 Four Channel Audio Support (RX1290/SWO/4AUD)
- 6.19 AAC Audio Support (RX1290/SWO/AAC)
- 6.20 Down Conversion (RX1290/SWO/DCONV)
- 6.21 Common Interface (RX1290/SWO/CI)
- 6.22 Provider Lock (RX1290/SWO/PROV/LOCK)
- 6.23 Web Browser Password Protection (RX1290/SWO/PW)
- re_e10228_07_6
- re_e10228_AA_6
- re_e10228_AB_6
- re_e10228_AC_6
- C Menus
- Contents
- C.1 LCD Menus
- C.2 Menu Pages - Main Menu
- C.3 The Menu Structure
- C.4 Presets Menu Items (Menu 1)
- C.5 Input Status Menu (Menu 2)
- C.6 Conditional Access Menu
- C.7 Service Menu (Menu 3)
- C.8 Transport Stream Output Menu
- C.9 Alarms Menu (Menu 6)
- C.9.1 Overview
- C.9.2 Transport Stream Alarm Setup Menu
- C.9.3 Video Alarm Setup Menu
- C.9.4 Audio 1 Alarm Setup Menu
- C.9.5 Audio 2 Alarm Setup Menu
- C.9.6 Audio 3 Alarm Setup Menu
- C.9.7 Audio 4 Alarm Setup Menu
- C.9.8 Satellite BER Alarm Setup Menu
- C.9.9 MER Alarm Setup Menu
- C.9.10 C/N Alarm Setup Menu
- C.9.11 Temperature Alarm Setup Menu
- C.10 System Menu (Menu 7)
- re_e10228_AD_6
- re_e10228_AE_6