Elmo ESD-CC1 User Manual
Multi-function cctv control keyboard, Esd-cc1 users’ manual
Table of contents
Document Outline
- ESD-CC1 Page3.pdf
- 1. General Introduction
- ESD-CC1 Page4.pdf
- 2. Front Panel & Real Panel
- 2.1 Front panel
- 2. Front Panel & Real Panel
- ESD-CC1 Page6.pdf
- 2.2 Rear connector panel
- 2.3 Switch setting on rear connector PCB
- ESD-CC1 Page7.pdf
- 3. Installation
- 3.1 RS485 cable
- 3.2 Cable connections
- 3. Installation
- ESD-CC1 Page8.pdf
- 4. Operations
- 4.1 Power On
- 4.2 Camera Control Mode
- 4. Operations
- ESD-CC1 Page9.pdf
- 4.2.1 OSD camera setting
- 4.2.2 Joystick
- 4.2.3 Set Preset and Run Preset
- 4.2.4 Sequence setting and execution
- ESD-CC1 Page10.pdf
- 4.2.5 Auto-Pan
- ESD-CC1 Page11.pdf
- 4.2.6 Cruise
- ESD-CC1 Page12.pdf
- 4.2.7 Zoom/Focus Lens control
- 4.2.8 Camera setting
- Camera Setting Mode
- 4.2.8.1 Auto Turn-Around
- ESD-CC1 Page13.pdf
- 4.2.8.2 Zoom speed setting
- 4.2.8.3 Digital Zoom ratio
- 4.2.8.4 Alarm Setup
- ESD-CC1 Page14.pdf
- 4.2.8.5 Speed by Zoom
- 4.2.8.6 Set PAN bias
- ESD-CC1 Page15.pdf
- 4.2.8.7 Set TILT bias
- 4.2.8.8 Check Camera Version
- 4.2.8.9 Auto Save Function.
- 4.2.8.10 Line Lock Phase Adjust Function.
- 4.2.8.11 Receiver Auxiliary Switch Function.
- 4.3 System Setting Mode
- ESD-CC1 Page16.pdf
- 4.3.1 System Linking
- 4.3.2 Set Keyboard ID
- 4.3.3 System monitor setting
- ESD-CC1 Page17.pdf
- 4.3.4 RS-232 Baud rate setting
- 4.3.5 Date Setting
- 4.3.6 Time Setting
- ESD-CC1 Page18.pdf
- 4.3.7 System Date/Time Correction
- 4.3.8 System Alarm List
- 4.3.9 Camera Type & Class
- ESD-CC1 Page19.pdf
- 4.3.10 Key Press Beep
- 4.3.11 Alarm Reaction
- 4.3.12 Password Set
- 4.4 Multiplexer Control
- ESD-CC1 Page21.pdf
- 5. Troubleshooting
- ESD-CC1 Page22.pdf
- Appendix A. RS485 Communication
- A.1 Connector (RJ-11 6P6C)
- A.2 ID Address Mapping
- Appendix A. RS485 Communication
- ESD-CC1 Page23.pdf
- Appendix B. Technical Specifications
- ESD-CC1 Page24.pdf
- Appendix C. The Architecture of SuperMPX and SuperMMX
- ESD-CC1 Page26.pdf
- Appendix D. Commands Tree of Operating and Setting
- ESD-CC1 Page28.pdf
- Appendix E. Software upgrade
- ESD-CC1 Page28.pdf
- Appendix E. Software upgrade
- ESD-CC1 Page28.pdf
- Appendix E. Software upgrade
- ESD-CC1 Page28.pdf
- Appendix E. Software upgrade
- ESD-CC1 Page04.pdf
- ESD-CC1 Page05.pdf
- ESD-CC1 Page06.pdf
- ESD-CC1 Page07.pdf
- ESD-CC1 Page08.pdf
- ESD-CC1 Page09.pdf
- 4.2.1 OSD camera setting
- 4.2.2 Joystick
- 4.2.3 Set Preset and Run Preset
- 4.2.4 Sequence setting and execution
- ESD-CC1 Page10.pdf
- ESD-CC1 Page11.pdf
- ESD-CC1 Page12.pdf
- ESD-CC1 Page13.pdf
- ESD-CC1 Page14.pdf
- ESD-CC1 Page15.pdf
- ESD-CC1 Page16.pdf
- ESD-CC1 Page17.pdf
- 4.3.4 RS-232 Baud rate setting
- 4.3.5 Date Setting
- 4.3.6 Time Setting
- ESD-CC1 Page18.pdf
- ESD-CC1 Page19.pdf
- ESD-CC1 Page20.pdf
- ESD-CC1 Page21.pdf
- ESD-CC1 Page22.pdf
- ESD-CC1 Page23.pdf
- ESD-CC1 Page25.pdf
- ESD-CC1 Page27.pdf
- ESD-CC1 Page09.pdf
- ESD-CC1 Page17.pdf