Assembly – Powerfix Z15003 User Manual
Page 25
25
GB/MT
Q
Assembly
CAUTION! DANGER OF FIRE! Assemble
and use the product on a fireresistant surface only.
The following tools are required for
assembly:
7 x Open spanners (1 x 8 mm, 2 x 10 mm,
2 x 14 mm, and possibly 2 x 17 mm)
2 x Allen key
1 x Slotted head screwdriver (approx. 5 mm)
Follow these steps:
j
Fasten the saddle
33
on to the base plate
32
with the hexagonal socket head screws
35
and washers
34
(see Fig. A).
j
Fasten the handle
3
on to the mount
36
with
the projecting screw thread and the corresponding
nut (see Fig. A).
Note: Please bear in mind that the angle
grinder must be fitted with a suitable cutting
disc before assembly. It is not possible to
change the disc with the angle grinder installed
in the stand.
j
Now mount the angle grinder in the mount
36
.
Note: At this point, first check the size of the
handle thread of your angle grinder. It may be
M6, M8 or M10.
j
Then place the corresponding mounting bolts
9
,
10
,
11
, washers
8
and matching nuts
12
,
13
,
14
, distance pieces
15
,
16
,
17
and plastic
bushings
6
,
7
to one side, ready for use.
j
Insert the necessary plastic bushings
6
,
7
into the mounting pieces
18
,
38
(see Fig. B).
Note: Ensure that the size of the plastic bush
ings
6
,
7
matches the required mounting
bolts
9
,
10
. Plastic bushings are not required
for mounting bolts M10
11
.
j
Screw the matching mounting bolt
9
,
10
,
11
through the rear mounting piece
38
(see Fig. B).
j
Fasten the rear mounting piece
38
in place by
tightening the corresponding size of nut
12
,
13
,
14
on the mounting bolt
9
,
10
,
11
(i.e. by
turning it in the direction of the mounting piece
38
)
(see Fig. B).
j
Insert the adjustment screw
20
through the bot
tom hole and the adjustment screw
1
through
the top hole of the mount
36
. Note that later
the rubber buffers of these screws must lie
against the angle grinder housing.
Note: First insert these screws so that the rubber
buffers lie directly against the mount
36
.
j
Now push the plastic locating pieces
19
of the
mounting pieces
18
,
38
on to the guide of the
mount
36
(Figure B).
j
Then attach the mounting pieces
18
,
38
through the plastic locating pieces
19
with the
hexagonal socket head screws
31
in the elon
gated holes in the mount
36
(see Fig. A).
j
Place the desired distance piece
15
,
16
,
17
on
the mounting bolt
9
,
10
,
11
and washer
8
on to the front mounting piece
18
(see Fig. D).
Note: The three distance pieces
15
,
16
,
17
are of different lengths. Choose the distance
piece
15
,
16
,
17
of the most appropriate length.
Note: Set the distance piece
15
,
16
,
17
so
that the cutting disc cannot come into contact
with the workbench / table below the base
plate
32
(see Figure E).
j
Screw the matching mounting bolt
9
,
10
,
11
through the front mounting piece
18
.
j
Fasten the front mounting piece
18
in place by
tightening the corresponding size of nut
12
,
13
,
14
on the mounting bolt
9
,
10
,
11
(i.e. by
turning it in the direction of the mounting piece
18
).
j
Now set the adjustment screws
1
,
20
so that
the angle grinder is aligned at right angles to
the base plate
32
and firmly attached to the
mount
36
.
j
After slightly loosening the hexagonal socket
head screws
35
, adjust the saddle
33
so that
the cutting disc of the angle grinder lowers into
centre of the slot provided in the base plate
32
.
j
Now attach the safety guard
5
. To do this
push the safety guard
5
on to the metal rod
2
and fasten it in place with the nut
4
(see Fig. C).
j
Now insert the metal rod
2
into the corre
sponding opening in the mount
36
and fasten
it in place with the nut
39
and the mounting
bolt
40
(see Fig. C).
j
Always keep the angle grinder’s mains lead in
place using the clip
37
.
j
After assembly is complete, switch the angle
grinder on for a few seconds and then switch it
79200_ES_IT_PT_content.indd 25
9/3/2012 1:02:01 PM