Sealey MA10 User Manual
Ma10.v2, Wood mortising attachment, Instructions for
InstructIons for:
WOOD MORTISING ATTACHMENT
MoDEL no:
MA10.V2
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
3. ASSEMbLY & USE
2. INTRODUCTION & CONTENT
WARNING! Ensure Health & Safety, local authority, and general
workshop practice regulations are adhered to when using this
equipment.
familiarise yourself with the applications and limitations of the
mortising attachment, as well as the potential hazards.
WARNING! Disconnect the drill from the mains power and ensure
the spindle is at a complete standstill before changing accessories.
Maintain the
mortising attachment in good condition.
replace or repair damaged parts. Use genuine parts only.
Unauthorised parts may be dangerous and will invalidate the
warranty.
Keep work area clean, uncluttered and ensure adequate lighting.
Keep tool bits and chisels clean and sharp for best and safest
performance.
WARNING! Always wear approved eye or face protection when
using the mortising attachment. use a face or dust mask if dust is
generated.
WARNING! DO NOT wear gloves when operating a pillar drill.
Keep hands and body clear of the work table when operating the
mortising attachment.
Maintain correct balance and footing. Ensure the floor is not
slippery and wear non-slip shoes.
remove ill fitting clothing. remove ties, watches, rings and other
loose jewellery and contain and/or tie back long hair.
Keep children and unauthorised persons away from the work area.
Ensure the workpiece is correctly secured before operating the
mortising attachment.
remove adjusting keys and wrenches from the machine and its
vicinity before turning it on.
DO NOT use the mortising attachment
for any purpose other than
that for which it is designed.
DO NOT operate the mortising attachment if any parts are damaged
or missing, as this may cause failure and/or personal injury.
DO NOT switch the mortising attachment on whilst the bit or chisel
is in contact with the workpiece.
DO NOT hold the workpiece by hand. use the clamps provided to
secure the workpiece.
DO NOT allow untrained persons to operate the mortising attachment.
DO NOT operate the mortising attachment
when you are tired or
under the influence of alcohol, drugs or intoxicating medication.
When not in use store in a safe, dry, childproof area.
Numbers in brackets refer to the item numbers as shown in the
parts diagram.
3.1. Loosely fit bolt (2) and nut (3) to chisel holder (1).
3.2. Mount the chisel holder (1) over the base of the drill quill, using
one of the three reducers (14) if necessary, and clamp in place
by tightening nut (3). the threaded hole for thumb screw (4a)
at base of chisel holder (1), should be facing directly forward.
3.3. screw thumb screw (4a) into the threaded hole.
3.4. Insert drill bit shaft and the chisel shaft up through the hole at the
base of the chisel holder (1) so that drill bit shaft enters chuck.
3.5. With the shoulder on the chisel approximately 1/32” (0.8mm)
from the base of the chisel holder (1) lightly clamp the chisel
by tightening the thumb screw (4a).
3.6. Push the drill bit up as far as it will go and tighten chuck jaws.
release thumb screw (4a) and push chisel up so that
shoulder contacts chisel holder (1), tighten thumb screw (4a).
this procedure will give the correct relationship between
the cutting edges of the bit and the points of the chisel.
3.7. Place 15/16” washers (7) on bolts (12) and then pass bolts
up through drill table and through fence (11) and rod holder (9).
clamp with 15/16” washers (7) and wing nuts (6).
3.8. slide steel rod (10) into central boss in rod holder (9) and
clamp with thumb screw (4b). slide arm (5) onto rod (10)
and clamp with thumb screw (4c).
3.9. clamp workpiece against fence (11) by using the two
hooked rods (8) through the rod holder (9), retained with
thumb screws (4d).
3.10. Lower arm (5) onto top of workpiece and clamp in position
with thumb screw (4c).
Note:If mortise is to go right through workpiece remember to
fix a 1/2” plywood panel between the workpiece and the
drill table to prevent chisel and bit striking the drill table.
3.11. Align chisel with workpiece and commence cutting mortise.
suitable for use with sealey and other leading makes of drill.
supplied with three chisel and bit sets and four mounting rings.
Mortising attachment is
not suitable for sealey's sDM30, GDM50B,
GDM150B, GDM180B, GDM200f, GDM200f/Vs, PDM240f and
PDM260f models.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, suffolk Business Park
,
Bury st. Edmunds, suffolk,
IP32 7Ar
www.sealey.co.uk
Web
Original Language Version
MA10.V2 Issue no: 2 10/01/12