Sealey ES550 User Manual
Es550.v3, Model no, Instructions for

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions and properly maintained,
give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
INSTRUCTIONS FOR:
E N G I N E S TA N D
Model No
:
ES550.V3
ITEM
pART No.
DESCRIpTION
1
ES550.V3-01
MAIN POST
2
ES550.V3-02
FRONT LEG
3
ES550.V3-03
MAIN POST SUPPORT
4
ES550.V3-04
BOLT (½” x 3½”)
5
ES550.V3-05
LOCKING WASHER (½”)
6
ES550.V3-06
HEx NUT (½”) NC
7
ES550.V3-07
BOLT (½” x 1”)
8
ES550.V3-08
HEAD MOUNTING PLATE
9
ES550.V3-09
LOCKING PIN
10
ES550.V3-10
MOUNTING ARM
11
ES550.V3-11
BOLT (½” x 2½”)
12
ES550.V3-12
FLAT WASHER (½”)
13
ES550.V3-13
HEx NUT (½”)
15
ES550.V3-15
ROTATION HANDLE
16
ES550.V3-16
MAIN POST LABEL
17
ES550.V3-17
REAR WHEEL (4”)
18
ES550.V3-18
CASTER WHEEL, FRONT
19
ES550.V3-19
BOLT (5/16” x 5/8”)
20
ES550.V3-20
HEx NUT (5/16”) NC
Note: The following numbers refer to Fig.1 and the parts list below.
3.1. Remove head mounting plate (8) from main post (1).
3.2. Loosely attach main post (1) to main post support (3) with
bolts (4), washers (5) and nuts (6).
3.3. Attach front legs (2) into main post support (3) and loosely
secure with bolt (7 & 4), washers (5) and nuts (6).
3.4. Fit front castors (18) to castor legs (2) with nuts (20) and
bolts (19).
3.5. Refit head mounting plate (8) to main post (1) and locate with
locking pin (9).
3.6. Attach the four mounting arms (10) to head mounting plate (8)
with bolts (11), washers (12) and nuts (13).
3.7. Insert handle (15) through hole in stem of mounting plate (8).
3.8. Apply weight evenly across the main post support (3) and front
legs (2), making sure that all four castor wheels are on level
ground and the frame is sitting square and true, then tighten
all nuts and bolts. Remove weight and check that the unit
is sitting correctly with all four castors in contact with the
ground.
WARNING! Ensure all Health and Safety, local authority, and general workshop
practice regulations are strictly adhered to when using this equipment.
Before using the stand ensure it is in good working order.
Replace or repair damaged parts. Use recommended parts only. Unauthorised
parts may be dangerous and will invalidate the warranty.
Keep the stand clean for best and safest performance.
Locate the stand in a suitable work area, keep area clean and tidy and
free from unrelated materials. Ensure there is adequate lighting.
Use on a firm, level surface capable of sustaining the stand and the load.
Maintain correct balance and footing. Ensure the floor is not slippery and
wear non-slip shoes.
Ensure all non-essential persons keep a safe distance whilst the stand is in
use.
Lock mounting plate in position with locking pin before fixing a load and ensure
the load is centred and securely mounted on the mounting plate.
When an engine is mounted, take the weight of the engine on the handle
before removing the locking pin.
Ensure the stand and load are stable.
To move a loaded stand, steady the load and push from behind the main
post of the stand so that the castor wheels are ahead of the load.
DO NOT pull the unit backwards, or push from the side, as this may cause
the stand to tip.
Ensure surface over which the stand is to travel is strong enough to take
the stand and load and that it is not cracked, uneven or obstructed.
DO NOT use unit if damaged.
DO NOT allow untrained persons to use the stand.
DO NOT exceed the rated capacity of 550kg.
DANGER! DO NOT work under an engine mounted on the stand.
DO NOT use the stand for purposes other than those for which it is designed.
When not in use, store in a safe, dry, childproof location.
3. ASSEMBLY
4. pARTS
2. SpECIFICATION
IMPORTANT: pLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OpERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS pRODUCT
CORRECTLY AND WITH CARE FOR THE pURpOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR pERSONAL INJURY AND
WILL INVALIDATE THE WARRANTY. pLEASE KEEp INSTRUCTIONS SAFE FOR FUTURE USE.
Maximum capacity: ........ 550kg
Width: ..........................790mm
Length:.........................950mm
Height: .........................930mm
Fig.1
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMpORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
Original Language Version
ES550.V3 Issue: 2 - 24/08/11