Sealey VS1003 User Manual
Axle stand 3 tonne ratchet type, Model no: vs1003, Instructions for
Ensure axle stands are in good order and condition. DO NOT use if damaged.
When centre column has been inserted into stand ensure the locking tab (Fig.1) is bent inward to stop the column from coming out.
Apply vehicle handbrake and chock wheels before jacking and using axle stands (in automatic vehicles select ‘Park’)
Raise centre column of axle stand and ensure the centre of the saddle is located under vehicle's jacking point. Refer to vehicle's handbook for jacking points.
Ensure the centre column is locked with the locking lever down and pawl engaged with a ratchet tooth (Fig.2).
Danger! Great care must be taken to ensure you lower the vehicle slowly and carefully onto the centres of the axle stands.
Ensure that vehicle and axle stands are stable before starting any work.
DO NOT use on soft ground or tarmacadam. Use on concrete only.
DO NOT use single axle stands. Only use in pairs.
DO NOT support more than the maximum capacity, as written on the axle stand (i.e. 3 Tonnes each, 6 Tonnes per pair).
DO NOT use four axle stands on one vehicle.
DO NOT jack one end of vehicle if the other end is already on axle stands, as the load is very likely to topple over.
DO NOT use for three wheeled vehicles or trailers. Refer to manufacturer’s instructions.
DO NOT use axle stands if damaged.
DANGER! Do not load axle stands beyond rated capacity. Overloading can cause damage to, or failure of the axle stands. POSITION
LOAD ON CENTRE OF SADDLE ONLY. ALWAYS USE AXLE STANDS IN PAIRS ON HARD LEVEL SURFACE CAPABLE OF SUSTAINING
THE LOAD. USE OF AXLE STANDS ON OTHER THAN HARD LEVEL SURFACES CAN RESULT IN LOAD INSTABILITY AND POSSIBLE
LOSS OF LOAD. DO NOT USE ON TARMACADAM. Failure to follow these instructions may result in damage to the axle stands, loss of load,
resulting in property damage, serious personal injury, or loss of life.
WarnIng: The warnings, cautions and instructions set out in this manual cannot cover all possible conditions and situations
that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must
be applied by the operator/owner.
INSTRUCTIONS FOR:
AXLE STAND 3 TONNE
RATCHET TYPE
MODEL No:
VS1003
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
3. PREPARATION
5.1.
Before each use, check that the axle stands and the stand's welds are not cracked and that there are no missing or damaged parts.
Any suspect axle stand must be removed from service immediately.
5.2.
Due to the potential hazards associated with these axle stands, do not misuse, or make any modification to the axle stands or components.
5.3.
It is the responsibility of the owner to ensure that the operator has read these instructions together with the safety features on the
side of the axle stand and that the operator is familiar with the axle stand’s use and limitations.
3.1.
Insert centre column into base of axle stand (Fig.2). Ensure toothed side of
column will engage with locking lever mechanism.
3.2.
Bend in locking tab using a small chisel and hammer (Fig.1).
3.3.
Check axle stand is in good condition and has not suffered damage during transit.
1. SAFETY INSTRUCTIONS
2. SPECIFICATION
IMPOrTanT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. RETAIN INSTRUCTIONS FOR FUTURE USE.
Capacity:. . . . . . . . . . . . . . . . . . . . . . . . 3 Tonnes Each / 6 Tonnes per Pair
Minimum Height: . . . . . . . . . . . . . . . . . 287mm
Maximum Height: . . . . . . . . . . . . . . . . . 427mm
4. OPERATION
5. MAINTENANCE & INSPECTION
Fig.2
Fig.1
4.1.
Refer to vehicle's handbook for correct jacking procedure. Check to ensure
manufacturer’s recommended jacking points are in good condition.
4.2.
Position axle stands under jacking points.
4.3.
To adjust axle stands: Hold locking lever up, while lifting column to required
height. Push locking lever down to lock pawl into column teeth (Fig.2).
WARNING! ENSURE PAWL IS FULLY ENGAGED WITH TEETH.
4.4.
Carefully and slowly lower vehicle onto axle stands. Ensure load bearing
points sit in the centre of the saddles and that the axle stands are stable.
Danger! You must follow instructions carefully and ensure you DO NOT
load the axle stands off-centre. Failure to heed these warnings may cause
damage, injury or loss of life.
nOTe: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business
Park
, Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
Original Language Version
VS1003 Issue: 1 - 24/12/09
Ratchet type axle stands with cast iron support posts. Feature angled teeth in posts, which prevent
accidental release of load - the more weight applied, the tighter the post is locked.
Bend tab in after
inserting Centre
Column