Sealey SM28 - Manual (Page 2)

3. ASSEMBLY INSTRUCTIONS
3.1. Remove parts from packing and take items out of the tank. Before assembly check parts to ensure they are complete and not damaged.
3.2. Close lid (4) of tank (1), gently turn unit upside down. Rest tank on a clean soft surface (i.e. cardboard) ensuring lid is secured in the closed position.
3.3. Attach the four legs (21) to the tank brackets with the pan head screws, spring washers and hex nuts (22, 23, 24) but do not tighten.
3.4. Place the lower shelf (20) between the four legs (21) with flat surface facing downward and fix with screws, washers and hex nuts (22, 23, 24).
3.5. With the legs pressed tightly against the lower shelf, tighten all the screws commencing with those attaching the shelf.
3.6. Fit one castor wheel assembly (47) to each rear leg, and one lockable wheel (46) to each of the front legs, and secure in place with a nut (48) and washer
(49) on each.
3.7. Hold the lid closed and stand the assembled unit upright. Open the lid but do not extend the lid too far.
3.8. Place the tank work shelf (42) on the two welded supports located inside the tank.
3.9. Remove the self tapping screws (35) from the cover of the pump unit and check to see if there is any supporting packing inside. If so, remove the
supporting packing and replace the cover and tighten the screws.
3.10. Place the pump into the tank unit and pass the switch unit through the slot in the cleaning tank side. As the unit protrudes through the slot, secure it by
placing the underside lip over the edge of the tank. Attach the flexible pipe (27) to the pump.
Refer to Parts list & Diagrams for item numbers.
4. OPERATING INSTRUCTIONS
 WARNINg! Wear safety clothing, eye protection and gloves and ensure you read, understand and apply the safety instructions in Section 1.
4.1. Ensure the unit is located on a firm level surface in a well ventilated area and is switched off and unplugged from the mains power supply.
4.2. Fill the tank with solvent (see below), tank capacity is 50 litres. Minimum level must cover pump inlet, approximately 40 litres. Follow the solvent's
instructions on its packaging.
4.3. Plug the unit into the mains power supply and switch the unit on. The cleaning agent will flow through the flexible tube.
4.4. Place parts to be washed into the basket, or directly into the tank. Direct solvent flow onto parts. Heavily soiled items may be left to soak before cleaning.
4.5. Do not leave the unit operating unattended. Check the fluid level does not fall below the pump inlet.
4.6. When cleaning is complete, remove all parts, whilst ensuring the minimum of cleaning agent spillage.
4.7. Switch off the unit, close the lid and disconnect the unit from the mains power supply. Clean up any spillage.
4.8. Dispose of waste liquids in accordance with local authority regulations.
IMPORTANT! The SM28 has an anti-fire device built into the unit. In the event of a fire, the lid will automatically close.
DO NOT prop the lid open as this will prevent the automatic safety feature from operating.
When cleaning parts, ensure that nothing in the tank, including any parts basket, is in a position that would prevent the lid from closing fully, if and when the
fusible link activates.
Once actuated, the fire detection device cannot be re-used and must be replaced before further use.
Sealey Cleaning Solvents available:
Degreasing Solvent Emulsifiable:. . . .25ltr. . . . . . . AK25
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20ltr. . . . . . . AK20
Degreasing Solvent: . . . . . . . . . . . . . .25ltr. . . . . AK2501
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20ltr. . . . . AK2001
5. MAINTENANCE
5.1. Clean the inside of the tank at regular intervals and keep the main body of the unit clean.
5.2. Regularly wash the pump filter in clean degreaser and replace it if necessary.
5.3. Ensure that all screws and bolts are kept tight.
2. SPECIFICATION
Pump Output: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200ltr/hr
Max. Tank Capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50ltr
Min. Working capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . .40ltr
Motor Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25W
Power Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V
Overall Height x Length x Width . . . . . . . 898 x 810 x 540mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32kg
Solvent type . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water soluble
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534 [email protected]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business
Park , Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
email
Original Language Version SM28 Issue: 1 - 24/05/11
Web
Heavy-duty one-piece tank. Fully sealed electric motor with magnetic drive pump unit. Lid features self-latching fusible link which automatically snaps lid shut in the
event of a fire. Includes removable shelf and small parts basket. Flexible metal nozzle directs solvent over work. Stand fitted with four Ø100mm castors for easy
manoeuvrability, two of which are lockable.
Environmental Protection.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycle centre and disposed of in a manner which is compatible with the environment.
When the product is no longer required, it must be disposed of in an environmentally protective way.
Contact your local solid waste authority for recycling information.
DO NOT dispose of waste cleaning solvent into drains, Contact your local waste authority for information.