Sealey SM222 User Manual
Page 2
DO NOT use the cleaning tank where there are flammable liquids, solids or gases.
DO NOT allow untrained persons to operate the cleaning tank.
DO NOT operate the cleaning tank if any parts are missing or damaged as this may cause failure or possible personal injury.
DO NOT leave the cleaning tank operating unattended.
DO NOT operate the cleaning tank when you are tired, under the influence of alcohol, drugs or intoxicating medication.
The tank is not suitable for paint thinners, gun wash or air drying.
When not in use switch the cleaning tank off, remove plug from the power supply.
Dispose of waste liquids in accordance with local authority regulations.
WARNING! DO NOT allow uncontrolled discharge of fluids thus polluting the environment.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
Original Language Version
© Jack Sealey Limited
SM222 Issue: 1 - 14/11/12
WARNING! Ensure that you have read, understood and apply the chapter 1 safety instructions before using the cleaner.
3.1.
Check that the cleaning tank power switch is in the off position, and that the unit is unplugged from the mains power supply.
3.2.
Fill the tank to appropriate capacity (between a minimum of 7.5ltrs and a maximum of 16ltrs) with Sealey soluable solvent (Part nos:
AK20,AK2001,AK25 and AK2501) or a general purpose water-soluable degreaser (contact your local dealer for supply).
DO NOT use
any other type of aggresive solvent (petroleum, toluene or thinners etc.)
CAuTION! Ensure that you follow any instructions provided
with the product.
3.3.
Remove plug from bottom of the cleaning tray to uncover mesh filter.
DO NOT operate without mesh filter in place.
3.4.
Plug the unit into the mains power supply and switch the unit on. Check that the solvent flows freely through the outlet hose.
3.5.
Place parts to be cleaned onto the cleaning tray. Use brush to remove dirt gently from parts to be cleaned.. Ensure any splash back
stays inside the tank.
3.6.
The brush can be placed temporarily in the pocket moulded into the lid. Ensure that the pump is switched off beforehand.
3.7.
Should any component require to be soaked, the drain plug can be inserted to allow a quantity of fluid to remain in the tray.
Ensure that the fluid drains back into lower tank afterwards.
3.8.
Turn off the pump and leave the parts to drain on the shelf.
3.9.
When complete, turn the cleaning tank off and unplug from the mains power supply.
3.10. Keep the cleaning tank clean. Remove and clean the mesh filter regularly for the best and safest performance.
3.11. The cleaning fluid can be re-used until it gets too dirty to be effective, at which point it needs changing.
3.12. To drain spent fluid, remove drain cap on the left hand side of the unit and drain into a suitable container.
WARNING! DO NOT allow uncontrolled discharge of fluids, thus polluting the environment. Dispose of waste liquids according to local
authority regulations.
2. APPLICATION & SPECIFICATIONS
3. OPERATING INSTRUCTIONS
Model No: ....................................................................................................SM222
Dimensions: ........................................................250mmH x 660mmW x 460mmD
Weight: ..............................................................................................................5kg
Power Supply: ................................................................................................230V
Motor Power ....................................................................................................16W
Pump output: ....................................................................................... 1000ltr/hour
Minimum Working Capacity: .......................................................................... 7.5ltr
Maximum Working Capacity: .......................................................................... 16ltr
●
Blow-moulded parts cleaning tank with brush.
●
Lightwieight and mobile unit suitable for bench-top mounting.
●
Fluid recirculated through filter and directed onto workpiece through long reach hose and brush.