Sealey SM914 - Manual (Page 2)

 Always work in a well ventilated area. Whenever possible use
the dust collection outlets provided on the machine.
 Take care that the belt and disc sander cannot tip over or move
while sanding long or heavy objects. If necessary, fasten the
belt and disc sander to a supporting surface.
 Ensure that the sanding belt is running in the correct direction
and ensure that the sanding disc or sanding belt is not
damaged.

DO NOT allow children or untrained persons to operate the
sander. Keep them away from the work area.
 Ensure the sanding belt is correctly positioned and adjusted so
that it cannot run off the pulleys.
 DO NOT remove the safety guard whilst sander is in use.
 Remove ill fitting clothing, ties and loose jewellery and tie back
long hair. Keep hands and body clear of the worktable when
operating the sander.
 DO NOT use the belt and disc sander near flammable liquids,
gases or dust.
 DO NOT disassemble the machine and do not try to repair it
yourself. Have the unit repaired by a professional or contact
your local Sealey dealer. Always use original replacement parts.
 DO NOT touch the sanding belt immediately after operation; it
may be extremely hot and cause burns. The sanding belt is
sharp-edged.

DO NOT use excessive force against the sanding belt or disc.
 DO NOT operate the sander when you are tired, under the
influence of alcohol, drugs or intoxicating medication.
 DO NOT get the sander wet or use in damp or wet locations or
areas where there is condensation.
 DO NOT switch the sander on while the workpiece is in
contact with the abrasive and DO NOT leave the sander
running unattended.
2. INTRODUCTION
3. TECHNICAL SPECIFICATION
Model No: ................................................................................. SM914
Belt Size: .........................................................................915 x 100mm
Belt Speed: ..........................................................................440mtr/min
Disc Size: ...............................................................................Ø150mm
Disc Speed: ............................................................................ 2850rpm
Table Size: .......................................................................230 x 160mm
Table Tilt: ......................................................................................0-45°
Motor Power: ............................................................................... 370W
Supply:.......................................................................................... 230V
Dust Extraction: ........................................................................Ø62mm
Weight: .......................................................................................18.5kg
Replacement Sanding Belts: ..............................................................
Model No: .................................................................................Grade:
SM14/B060G ...............................................................................60Grit
SM14/B080G ...............................................................................80Grit
SM14/B100G .............................................................................100Grit
Replacement Sanding Discs: .............................................................
Model No: .................................................................................Grade:
SM14/D80G .................................................................................80Grit
Bench mounting semi-portable belt and disc sander suitable for
general woodworking applications. Powerful induction motor with
smooth, bearing-mounted drive pulleys gives quiet operation. The
sanding belt can be used in a vertical or horizontal position and at any
other angle inbetween. The sanding disc table can be tilted to any
angle up to 45°, and is supplied with a mitre gauge for accurate angle
sanding.
fig.1
A MITRE GAUGE
B KNOB FOR TABLE ANGLE
ADJUSTMENT (Not visible)
C DRIVE DRUM
D BELT SANDING GUARD
E BELT TENSIONING LEVER
F SANDING BELT
G BELT TRACKING CONTROL
H IDLER DRUM
I MOUNTING POINT x 3
J ON/OFF SWITCH
K SANDING DISC
L DISC SANDING TABLE
M DUST EXTRACTION PORT
(Not visible)
4. ASSEMBLY & ADJUSTMENT
WARNING! Ensure that the sander is disconnected from the
mains power supply before beginning assembly.
4.2 Attaching the sanding disc abrasive pad and lower cover.
4.2.1 Before attaching cover (C) in place, remove the backing from
the self adhesive abrasive pad and stick it to the metal disc
ensuring that it is centralised. Fix the lower cover (C) in place
as shown above using two self tapping screws (A&B).
4.1 Mounting the sander.
4.1.1 Mount the sander to a suitable workbench adjacent to dust
extraction facilities if available. Bolt the sander down utilising
the three mounting holes, two in the left hand flange and one
on the right hand flange. Insert bolts from above and fasten
below with nuts and lock washers.
4.3 Attaching the sanding disc table.
4.3.1 The sanding disc table has one pivot/fixing point as indicated
above which plugs directly into the main body of the sander
and is held in place by a single clamping knob as shown in
fig.4.
fig.2
© Jack Sealey Limited Original Language Version SM914 Issue No.1 07/12/12
fig.3