Sealey PC40 User Manual
Pc40.v2, Instruction manual for: model, Safety instructions
INSTRUCTION MANUAL FOR:
MODEL:
PC40.V2
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
p
WARNING! The blade used by this cutter is razor sharp and should be treated with due caution.
3
Store the cutter in a safe childproof place when not in use.
3
Use in a suitable, clean and tidy work area, free from unrelated materials. Ensure there is adequate lighting.
3
Use the cutter for rubber and soft vinyl pipes only.
7
DO NOT use cutter on hard reinforced pipe. If the blade does not penetrate the pipe, then the material
used to make the pipe is too hard. Applying excessive pressure may cause the pipe to shatter.
7
DO NOT continue to attempt cutting any pipe that withstands penetration.
7
DO NOT insert a finger into the cutting area at any time.
7
DO NOT turn the pipe whilst cutting.
7
DO NOT allow untrained people to use the cutter.
7
DO NOT allow children to use or play with the cutter.
7
DO NOT use the cutter for tasks it is not designed to perform.
7
DO NOT operate cutter if any parts are damaged or missing as this may cause failure and/or personal injury.
7
DO NOT operate the cutter when you are tired or under the influence of alcohol, drugs or intoxicating medication
.
PC40.V2 - 1 - 051005
2.
INTRODUCTION
Pistol-type, ratchet action, die-cast aluminium alloy body with heat treated AUS-8 stainless steel blade honed and
shaped for smooth cutting action. Ratchet cutting action avoids crushing pipe. Long-life blade suitable for cutting
extrusions and pipes. Textured grip with rubber inlay gives added comfort and control.
Cutting capacity
6 - 42mm OD
PLASTIC PIPE AND E X T R U S I O N C U T T E R
PART NUMBER FOR SPARE BLADE
PC40/B
INSTRUCTION MANUAL FOR:
MODEL:
PC40.V2
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
p
WARNING! The blade used by this cutter is razor sharp and should be treated with due caution.
3
Store the cutter in a safe childproof place when not in use.
3
Use in a suitable, clean and tidy work area, free from unrelated materials. Ensure there is adequate lighting.
3
Use the cutter for rubber and soft vinyl pipes only.
7
DO NOT use cutter on hard reinforced pipe. If the blade does not penetrate the pipe, then the material
used to make the pipe is too hard. Applying excessive pressure may cause the pipe to shatter.
7
DO NOT continue to attempt cutting any pipe that withstands penetration.
7
DO NOT insert a finger into the cutting area at any time.
7
DO NOT turn the pipe whilst cutting.
7
DO NOT allow untrained people to use the cutter.
7
DO NOT allow children to use or play with the cutter.
7
DO NOT use the cutter for tasks it is not designed to perform.
7
DO NOT operate cutter if any parts are damaged or missing as this may cause failure and/or personal injury.
7
DO NOT operate the cutter when you are tired or under the influence of alcohol, drugs or intoxicating medication
.
PC40.V2 - 1 - 051005
2.
INTRODUCTION
Pistol-type, ratchet action, die-cast aluminium alloy body with heat treated AUS-8 stainless steel blade honed and
shaped for smooth cutting action. Ratchet cutting action avoids crushing pipe. Long-life blade suitable for cutting
extrusions and pipes. Textured grip with rubber inlay gives added comfort and control.
Cutting capacity
6 - 42mm OD
PLASTIC PIPE AND E X T R U S I O N C U T T E R
PART NUMBER FOR SPARE BLADE
PC40/B