Sealey SM1305 - Manual (Page 2)

Unpack the product and check contents for damage. Should there be any damaged or missing parts contact your supplier immediately.
3.1. Stand Assembly
3.1.1. Assemble stand as shown in fig.1.N. Ensure all fittings are tight.
3.2. Saw Assembly
An assistant may be required to help.
3.2.1. To install the table, place table and support onto the sliding base support, sliding saw blade through the slot in table, and also ensuring
bolt (part 126) is in place and aligns with hole in base support.
3.2.2. Secure by threading adjustment knob onto bolt and tightening.
3.2.3. fit the bolt into the blade slot of table. Attach the table side guide to the table with four bolts and washers.
3.2.4. fit the fence, first align bearing at the far end with one of the table slots, then lower onto table side guide. Push down handle (fig.1.G)
to lock when fence is in required position.
3.2.5. Position table at right angles to the blade. Using a set square against the blade check for accuracy. If any adjustment is needed,
loosen nuts and bolts holding the sliding base support and make any necessary fine adjustments. Tighten all nuts and bolts.
3.2.6. Important! Attach the saw to the stand using appropriate bolts, nuts and washers, or alternatively to a firm, stable work surface
capable of supporting the saw and any workpiece.
DO NOT attempt to use the saw as a free-standing unit as it may topple over during use and cause damage and/or personal injury.
3.2.7. Connect extraction port (Ø100mm) to dust extractor system (if available).
1.2. GENERAL SAFETY Continued
 Disconnect the saw from the power supply before removing wood chips or dust.

Use a workpiece support when sawing material which extends beyond the saw table.

DO NOT operate the machine if damaged.

DO NOT operate the machine if any parts are missing as this may cause failure and/or personal injury.

DO NOT use saw blades which are damaged or deformed. Use only Sealey blades and spare parts. Non-standard blades can be
dangerous.

DO NOT get the saw wet or use in damp or wet locations or areas where there is condensation.

DO NOT expose the saw housing to flame or high temperature.

DO NOT allow untrained persons to operate the saw.

DO NOT use saw where there are flammable liquids, solids or gases such as paint solvents and including waste wipers or cleaning rags etc.

DO NOT leave the saw operating unattended.

DO NOT operate the saw if either of the blade covers is open or if the blade guard is not fitted.

DO NOT operate the saw when you are tired or under the influence of alcohol, drugs or intoxicating medication.

DO NOT use the saw for a task it is not designed to perform.

When not in use switch off the saw and unplug from the mains power.
fully approved to current CE regulations. Steel chassis with locking blade wheel covers. Bearing mounted blade wheels and belt drive induction motor
provide smooth operation. Micro switches prevent operation when either blade wheel cover is open. No-volt release switch prevents uncontrolled blade
re-start after power interruption. Suitable for cutting wood and plastics. fitted with tilting table for bevel and compound cuts. Supplied with quick
adjusting rip fence, mitre gauge, dust extraction port and sturdy metal stand.
3. ASSEmbLY
2. DESCRIPTION & SPECIFICATIONS
model No: . . . . . . . . . . . . . Sm1305 . . . . . . . . Sm1306
Throat Depth: . . . . . . . . . . . .305mm . . . . . . . . . 335mm
Max. Cutting Height:. . . . . . .180mm . . . . . . . . . 180mm
Table Size: . . . . . . . . . .500x400mm . . . . . 500x400mm
Table Tilt Adjustment: . . . . . . . 0-45° . . . . . . . . . . . 0-45°
Blade Length: . . . . . . . . . . .2240mm . . . . . . . . 2400mm
Cutting Speeds: . . 360 & 660m/min . . 540 & 660m/min
Motor Power: . . . . . . . . . . . . . 550W . . . . . . . . . 750W
Power Supply: . . . . . . 240V - 50Hz . . . . . 240V - 50Hz
Dust Extraction Port: . . . . Ø100mm . . . . . . . .Ø100mm
mAIN FEATURES
A Blade tension adjustment knob
b Blade cover lock
C Blade guard height locking knob
D Blade guard
E fence
F No Volt On/Off switch
G fence lock handle
H Table side guide
I Mitre guide
J Blade
K Drive belt tensioner knob
L Extraction outlet
m Tracking adjustment knob
N Stand
fig.2
fig.1
Original Language Version SM1305, SM1306 Issue:3 (SP) - 04/12/13 © Jack Sealey Limited