Sealey RE024 User Manual
Re024, Plastic repair staple gun - cordless, Instructions for
1.1.
GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
equipment.
WARNING! DO NOT touch the staple once it has been inserted into the staple gun and power has been switched on.
WARNING! High temperatures are reached and will inflict serious burns to skin upon contact with the staple.
WARNING! Allow to cool before removing any unused staples from the staple gun pin tip.
Familiarise yourself with the application, limitations and potential hazards of the staple gun.
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Locate staple gun in a suitable working area, keep area clean and tidy and free from unrelated materials.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
Keep the staple gun clean for best and safest performance.
Ensure there are no flammable or combustible materials near the work area.
Wear approved safety eye protection (standard spectacles are not adequate).
Wear heat resistant gloves and appropriate protective clothing.
Ensure the workpiece is adequately held before operating the staple gun.
Always use staple gun in a well ventilated atmosphere and wear Personal Protective Equipment.
Ensure that when the staple gun is put down during use that the tip is not near to or in contact with any material that may burn or melt.
After use always keep the staple gun in its original package in a safe place away from children.
DO NOT touch the staple during its warm up phase.
DO NOT use in wet or damp conditions.
InstRuctIons FoR:
pLASTIc REpAIR STApLE GuN - cORDLESS
modEL no:
RE024
1. SAFETY
Original Language Version
© Jack sealey Limited
DO NOT operate the staple gun
when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT leave a hot staple gun unattended. (If you are leaving the work area even for a short period of time switch it off and allow to cool.)
DO NOT use the staple gun for any purpose other than that for which it has been designed.
DO NOT allow untrained persons to operate the staple gun.
DO NOT touch the workpiece as it will be very hot. Allow to cool.
DO NOT operate the staple gun if damaged.
1.2. ELEcTRIcAL SAFETY FOR uSE OF cHARGER.
USE ONLY THE SUPPLIED CHARGER PLUG FOR CONNECTING TO THE POWER SUPPLY.
WARNING! It is the user’s responsibility to read, understand and comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An RccB (Residual current
circuit Breaker) should be incorporated in the main distribution board. We also recommend that an Rcd (Residual current device)
is used with all electrical products, particularly portable equipment which is plugged into an electrical supply not protected by an RccB.
You must also read and understand the following instructions concerning electrical safety.
1.2.1.
The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a
qualified electrician, using a Portable Appliance tester (PAt), at least once a year.
1.2.2.
The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator.
If in any doubt about electrical safety, contact a qualified electrician.
1.2.3.
You must ensure that you:
Inspect the charger plug, cable and connector for wear and damage to ensure items are safe before connecting to the mains power
supply. If worn or damaged
DO NOT use.
Important: check that the voltage marked on the charger plug is the same as the power supply to be used.
DO NOT pull the charger plug from the mains socket by the lead.
DO NOT use any other type of charger with this product.
DO NOT try to take the charger plug apart.
DO NOT use the charger plug to charge or power any other electrical item.
DO NOT get the charger wet, or use in wet, damp conditions (for indoor use only).
WARNING! NEVER substitute a standard 13amp 3 pin plug, or any other type of plug, for the charger plug.
1.3. BATTERY SAFETY
WARNING! to reduce the risk of burns or fire:
DO NOT attempt to open, disassemble, modify or service the battery pack.
DO NOT crush, puncture, short external contacts or dispose of in fire or water.
DO NOT expose to temperatures above 60°c (140°).
Recycle or dispose of used battery as stipulated by local regulation.
IMPORTANT: pLEASE READ THESE INSTRucTIONS cAREFuLLY. NOTE THE SAFE OpERATIONAL REQuIREMENTS, WARNINGS & cAuTIONS. uSE THE
pRODucT cORREcTLY AND WITH cARE FOR THE puRpOSE FOR WHIcH IT IS INTENDED. FAILuRE TO DO SO MAY cAuSE DAMAGE AND/OR
pERSONAL INJuRY AND WILL INVALIDATE THE WARRANTY. KEEp THESE INSTRucTIONS SAFE FOR FuTuRE uSE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
RE024 Issue: 1 - 09/04/14
Wear eye
Protection
Wear
Respiratory
Protection
Wear Heat
Resistant Gloves
Hot surfaces