Sealey HVLP01 User Manual
Sealey Tools
Locate the spray gun in a suitable work area. Keep this area clean and tidy and free from unrelated materials. Ensure that there is adequate
ventilation and lighting.
Familiarise yourself with the application, limitations and potential hazards peculiar to the spray gun.
WARNING! Disconnect the spray gun from the air supply before changing accessories, servicing or performing any maintenance.
Maintain the
spray gun in good condition (use an authorised service agent).
Replace or repair damaged parts. Use authorised parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Keep the spray gun clean for best and safest performance.
Ensure that the compressed air system can supply the spray gun air consumption for the model to be used.
Wear approved safety respiratory protection and safety eye goggles.
If spraying isocynate based finisher, wear approved respirator/clean air breathing apparatus and cover exposed skin with latex gloves and
an impervious hooded coverall.
Remove ill-fitting clothing. Remove ties, watches, rings and other loose jewellery and tie back long hair.
Keep children and unauthorised persons away from the work area.
When not in use, ensure that the air supply is turned off.
Avoid unintentional operation of the spray gun.
When not in use, disconnect the spray gun from the air supply, clean thoroughly and store safely.
DO NOT point spray gun at yourself, other persons or animals.
DO NOT direct air from the air hose at yourself, other persons or animals.
DO NOT carry the spray gun by the hose, or yank the hose from the air supply.
DO NOT exceed the working pressure of 43psi (3bar).
DO NOT use the spray gun for any purpose other than that for which it is designed.
DO NOT allow untrained persons to operate the spray gun.
DO NOT get the spray gun wet or use in damp or wet locations or in areas where there is condensation.
DO NOT operate the spray gun if any parts are missing or damaged as this may cause failure and/or personal injury.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may occur. It
must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be applied
by the operator
InsTRucTIons FoR:
HVLP GRAVITY FEED SPRAY GUN
1.4
mm
SET-UP
MoDEL no:
HVLP01
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREmENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO mAY CAUSE DAmAGE AND/OR PERSONAL
INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
1. SAFETY
2. INTRODUCTION
Gravity/suction feed spray gun designed for the professional workshop. Features air and paint flow controls for fine adjustment of spray pattern.
HVLP technology and precision engineering delivers consistant and unrivalled results. suitable for water based paints.
3. SPECIFICATION
model No: . . . . . . . . . . . . . . . . . . HVLP01
standard set up:.. . . . . . . . . . . . . . .1.4mm
Air Pressure:. . . . . . . . . . . . . . . . . 30-40psi
Air consumption:.. . . . . . . . . . . . . .14.5cfm
Pot capacity: . . . . . . . . . . . . . . . . . . 600ml
4. CONTENTS
HVLP01 Issue: 1 - 11/09/14
Original Language Version
© Jack sealey Limited
1
4
2
3
5
6
7
10
8
9
11
Item Description
Qty
1 Gun
1
2
1.4 Gun Head (MAX 10psi) 1
3
Pot (600ml)
1
4 strainer
1
5
universal spanner
1
6
Adaptable Key
1
7
socket (7mm)
1
8
cleaning Pin (Ø0.57mm)
1
9
cleaning Pin (Ø0.42mm)
1
10
Brush
(A)
1
11
Brush
(B)
1
4.1.
Empty contents from the product carton on to a tray or bench. In the unlikely event of missing or damaged parts, inform your
sealey dealer immediately.
4.2.
The spray gun has been treated with an anticorrosive agent at the factory and
mUST be flushed out thoroughly with thinner before use.
fig.1