Sealey HCC08 - Manual (Page 2)

notE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPoRTANT: No liability is accepted for incorrect use of this product. WARRANTy: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INfoRMATIoN: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
declaration of Conformity We, the sole importer into the UK, declare that the product listed below is in conformity with the following
standards and directives.
The construction file for this product is held by the Manufacturer and may be
inspected, by a national authority, upon request to Jack Sealey Ltd.
For Jack Sealey Ltd. Sole importer into the UK of Sealey Professional Tools.
21st October 2008 Signed by Tim Thompson
Paint Can Crusher
Model No. HCC08
93/68/EEC CE Marking Directive
2006/42/EC Machinery Directive
4.1 Place the empty paint can with its lid removed, open end
downwards in the centre of the crushing chamber.
4.2 Close the door ensuring the lock is full engaged. (The
crusher will not function until the door is firmly closed).
4.3 Turn the control lever (Fig.3) to the 'DOWN' position and
the piston will descend.
4.4 When the red line on the indicating rod (Fig.3) is level
with the main body the can is crushed. You can also
listen for the air to stop flowing (approx 20 seconds).
4.5 Turn the control lever to the 'UP' position, when the
piston has returned to the start position move the control
lever back to the centre 'STOP' position.
 WarnInG! never attempt to open the door until the
piston is fully retracted and the control lever is in
the 'Stop' position.
4.6 Open the door and remove the crushed can.
Note: You may crush several cans at the same time provided
they are all a similar height and providing you have
adequate air pressure.
Note: It is necessary to remove the catch basin and clean it
periodically. Dispose of solid residue according to local
authority guidelines.
Note: Leave the door ajar when not in use.
Tip: Crease the can with your fingers before putting in the
crusher. This will enable faster crushing and place less
strain on the crusher.
5. MAINTENANCE
4. oPERATIoN
 WarnInG! all inspection and maintenance
procedures must be with ram retracted.
5.1 Persons using the crusher should be properly trained in
its use including inspection of the unit prior to operation.
If the operator is in any doubt regarding the proper
functioning or structural integrity of the unit it should not
be used. Remove it from service immediately and
contact your local Sealey dealer.
5.2 If the unit is used daily it should be further inspected by
a qualified person on a weekly basis.
5.3 If the unit is used intermittently it should be further
inspected by a qualified person on a monthly basis.
5.4 All warning labels, instruction labels, and specification
labels should be complete and readable.
5.5 External surfaces of the unit can be washed with a mild
soap solution.
5.6 Periodically remove the paint collection tray and
clean/remove paint and other foreign matter.
5.7 Periodically oil all moving parts.
01284 757500
01284 703534 [email protected]
Sole UK distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
www.sealey.co.uk
Web
email
fig.2
fig.3
3.6 Air Supply.
Connect the air supply to the air inlet situated on the
regulator. The inlet connection is 1/4”BSP.
The recommended air hook-up procedure is shown in
Fig.2.
3.6.1 You will require a minimum air pressure of 100psi.
3.6.2 WARNING! Ensure the air supply is clean and does not
exceed 130psi whilst operating the paint can crusher.
Too high an air pressure and unclean air will shorten the
product life, and may be dangerous, causing damage
and/or personal injury.
3.6.3 Drain the air tank daily. Water in the air line will damage
the ram.
3.6.4 Clean compressor air inlet weekly.
3.6.5 Line pressure should be increased to compensate for
unusually long air hoses (over 8 metres).
3.6.6 Keep hose away from heat, oil and sharp edges. Check
hose for wear, and make certain that all connections
are secure.
The paint can crusher is now ready for use.
Screw
HCC08 Issue No: 1 23/10/08
Indicating Rod
Control Lever