Sealey AK100 User Manual
Sealey Tools

1.1 Safety Instructions
WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this
equipment.
Maintain the dent puller in good condition.
Replace damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
Before each use, check condition of dent puller. If any component is worn or damaged replace immediately.
WARNING! Always wear approved eye (or face) and hand protection when operating the puller.
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
Maintain correct balance and footing.
DO NOT over reach, ensure the floor is not slippery, wear non-slip footwear.
Keep fingers clear of suction release trigger during use.
Keep children and unauthorised persons away from the working area.
Ensure workpiece is secure before operating the dent puller.
Ensure that the workpiece surface is clean, dry and free from oil or grease.
DO NOT exceed the maximum pull capacity of the dent puller.
DO NOT clean the suction cups with solvents or other harsh chemicals.
DO NOT use the dent puller for any purpose other than that for which it is designed.
DO NOT use the dent puller if any parts are damaged or missing as this may cause failure and/or personal injury.
DO NOT use the dent puller when you are tired or under the influence of alcohol, drugs or intoxicating medication.
When not in use, store in a safe, dry, childproof location.
InStRUctIonS foR:
PROFESSIONAL DENT PULLERS
Ø75mm, Ø100mm, Ø125mm
ModEl no's:
Ak100, Ak101, Ak102
thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/
OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE kEEP INSTRUCTIONS SAFE FOR FUTURE USE.
2. INTRODUCTION & SPECIFICATION
4. MAINTENANCE
3. OPERATION
WARNING! Ensure that you read, understand and apply Section 1 safety
instructions.
3.1 Ensure that the workpiece is clean, dry and free from oil and grease.
3.2 Remove the protective cover from the suction cup.
3.3 Holding the handle, firmly push the dent puller into the centre of the dent.
3.4 Pull the dent puller outwards in a controlled manner until the dent has been
extracted.
3.5 lift the suction release trigger to remove the dent puller from the workpiece.
3.6 Refit the protective cover on the suction cup and store in a safe, dry, childproof
location.
4.1 check condition of suction cup regularly, if damaged replace using genuine parts only.
4.2 Keep dent puller in a clean, serviceable condition, use a damp cloth to clean.
2.1 Introduction
Specialist device for pulling dents from panels and bodywork. contoured aluminium handle and suction release trigger give
the technician close control.
2.2 Specification
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole Uk Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
Original Language Version
AK100, AK101, AK102 Issue: 1 - 18/07/12
© Jack Sealey limited 2012
Model No:
AK100
AK101
AK102
Size:
Ø75mm
Ø100mm
Ø125mm
Maximum Pull Capacity:
10kg
15kg
20kg
Parts support is available for this product. To obtain a parts listing and/or
diagram, please log on to www.sealey.co.uk, email [email protected] or phone 01284 757500.