beautypg.com

Sealey SSG2 User Manual

Suction feed refinishing gun, Ssg2.v2, Instruction for

background image

Ideal for applying base coats. Features adjustable paint flow and fan width controls. Supplied with

aluminium screw type suction feed pot. Suitable for use with waterborne paints. Alternative set-ups

available separately.

INSTRUCTION FOR:

SUCTION FEED

REFINISHING GUN

MODEL No:

SSG2.V2

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and

properly maintained, give you years of trouble free performance.

Standard Set Up: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5mm

Available Set ups:. . . . . . . . . . . . . . . . . . .1.2, 1.8, 2.0, 2.2 & 2.5mm

Nominal Operating Air Pressure: . . . . . . . . . . . . . . . . . . . . . . . 50psi

Nominal Air Consumption: . . . . . . . . . . . . . . . . . . . . . . . . 5 - 11cfm

Pot Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8l

Air Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4"BSP

2. INTRODUCTION & SPECIFICATIONS

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,

WARNINGS AND CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS

INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE

WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY INSTRUCTIONS

Familiarise yourself with the application and limitations, as well as the potential hazards of the spray gun.

WARNING! Disconnect the spray gun from the air supply before changing accessories, servicing or performing any maintenance.

Maintain the

spray gun in good condition (use an authorised service agent).

Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

Locate the spray gun in a suitable work area, keep area clean and tidy and free from unrelated materials, and ensure that there is

adequate ventilation and lighting.

Keep the spray gun clean for best and safest performance.

Ensure the air system has sufficient output for the spray gun air consumption (see specification).

Wear approved respiratory protection, safety eye goggles and skin protection.

Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and tie back long hair.

Keep children and unauthorised persons away from the work area.

When gun is not in use ensure the air supply is disconnected.

Avoid unintentional operation.

DO NOT paint were there is any source, or possible source, of ignition as paint mist is extremely flammable.

DO NOT point spray gun at yourself or at other persons or animals.

DO NOT carry the by the air hose, or yank the hose from the air supply.

DO NOT use the spray gun for any purpose other than for which it is designed.

DO NOT allow untrained persons to operate the spray gun.

DO NOT get the spray gun wet or use in damp or wet locations or areas where there is condensation.

DO NOT operate gun if any parts are missing or damaged as this may cause failure and/or personal injury.

DO NOT direct air from the air hose at yourself or others.

3. AIR SUPPLY CONNECTION

3.1. For recommended hook-up, see diagram (fig.1).

3.2. Ensure the air valve is in the "off" position before connecting to the air supply.

3.3. You will require an air supply capable of providing a pressure 50psi and an air volume of 11cfm to operate the gun.

3.4.WARNING! Ensure the air supply is clean and is regulated to a maximum of 50psi. Too high an air pressure and unclean

air will shorten the life of the gun due to excessive wear and may be dangerous, causing damage and/or personal injury.

3.5. Drain the air supply tank and pressure regulator daily. Water in the air line will damage the gun and contaminate the paint.

3.6. Clean the compressor air inlet filter weekly.

3.7. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be

10mm (3/8") I.D. and fittings must have the same inside dimensions.

3.8. Keep hose away from heat, oil and sharp edges. Check hoses for wear, and make certain that all connections are secure.

fig.1

Original Language Version

SSG2.V2 Issue: 2 - 18/01/10

This manual is related to the following products: