Sealey AK3984 - Manual

INSTRUCTIONS FOR:
LONG/SHORT ARM THREADED NUT RIVETER
MODEL No:'s
AK3984 & AK3985
r WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.
3 Familiarise yourself with the application and the limitations of the riveter, as well as the potential hazards.
3 Maintain the riveter in good condition (use an authorised service agent).
3 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
3 Keep the work area clean, uncluttered and ensure there is adequate lighting.
3 Keep the riveter clean for best and safest performance.
3 Check moving parts alignment on a regular basis.
7 DO NOT hold the workpiece by hand. Secure unstable workpiece with a clamp, vice or other adequate holding device.
3 Ensure the workpiece is correctly secured before using the riveter.
7 DO NOT use the riveter for any purpose other than that it was designed for.
7 DO NOT operate the riveter if any parts are damaged or missing, as this may cause failure and/or personal injury.
3 When not in use store in a safe, dry, childproof location.
r WARNING! Always wear approved eye or face protection when operating the riveter.
Original Language Version © Jack Sealey Limited
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AK3984 . . . . . . . . . . . . . . . . . . .AK3985
Length:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285mm . . . . . . . . . . . . . . . . . . . .410mm
Rivet Nut Sizes:
M3x0.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes . . . . . . . . . . . . . . . . . . . . . . .Yes
M4x0.7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes . . . . . . . . . . . . . . . . . . . . . . .Yes
M5x0.8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes . . . . . . . . . . . . . . . . . . . . . . .Yes
M6x1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes . . . . . . . . . . . . . . . . . . . . . . .Yes
M8x1.25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes . . . . . . . . . . . . . . . . . . . . . . .Yes
M10x1.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No . . . . . . . . . . . . . . . . . . . . . . .Yes
M12x1.75 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No . . . . . . . . . . . . . . . . . . . . . . .Yes
Rivet Type:
Aluminium . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes . . . . . . . . . . . . . . . . . . . . . . .Yes
Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes . . . . . . . . . . . . . . . . . . . . . . .Yes
Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes . . . . . . . . . . . . . . . . . . . . . . .Yes
Blind Rivets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No . . . . . . . . . . . . . . . . . . . . . . .No
Structural Rivets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No . . . . . . . . . . . . . . . . . . . . . . .No
Fig.1 Fig.2
AK3984 & AK3985 Issue No.2 - 12/06/14
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY . NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS . USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED . FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY . KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE .
Thank you for purchasing a Sealey product . Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance .
1 . SAFETY
2 . INTRODUCTION
3 . SPECIFICATION
Suitable for rivet nuts in aluminium, steel and stainless steel. Short arms (AK3984) provide effortless functionality and access in restricted spaces.
Long arms (AK3985) provide effortless functionality with adjustable stroke scale for improved accuracy.