Sealey MAT150AS - Manual (Page 3)

3.3. Dust Collection
3.3.1. Models MAT150AS & MAT110AS.
The dust outlet tube of the sander must be connected to a dust-free system in accordance with COSHH,
and any other regulations that may apply to the work area. For information on dust-free systems, contact
your local Sealey dealer.
3.3.2. Model MAT150SC only
This model has a dust bag included. Attach the dust extraction pipe to the machine outlet and secure it
with the worm drive clip provided. Insert the other end into the small opening at the bag head. Push the
tube half way into the bag. Secure with the ties. To empty the bag, wear appropriate dust mask, etc., open
the velcro end and empty contents according to disposal regulations. Do not place any liner in the bag as
this will inhibit the air flow.
4. OPERATING INSTRUCTIONS
5. MAINTENANCE
4.1. Attach a suitable sanding material to the velcro backing disc / pad.
4.2. Connect the sander to the air supply and to a dust free system if required (MAT150AS & MAT110AS).
Press the control valve (ON/OFF) lever and check that the unit is working correctly. Some models will have
an air flow control knob. Turn the knob to increase or decrease the air flow.
Note: The sander is designed for dry use only. DO NOT use with water or any other liquids.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534 [email protected]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park ,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email

WARNING! Disconnect sander from air supply before changing accessories, servicing or performing
maintenance. Replace or repair damaged parts. Use recommended parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
5.1. DO NOT oil the sander, or connect to an air supply which incorporates an oiler. Oiling will result in damage
to teflon surfaces within the sander.
5.2 Clean the sander after use and change pads when required.
5.3 Loss of power or erratic action may be due to the following:
a) Excessive drain on the air line. Moisture or restriction in the air pipe. Incorrect size or type of hose
connectors. To remedy, check the air supply and follow instructions in Section 3.
b) Grit or gum deposits in the tool may also reduce performance. If your model has an air strainer (located
in the area of the air inlet), remove the strainer and clean it. Flush the tool out with gum solvent
oil or an equal mixture of SAE 10 oil and kerosene. Allow to dry before use.
c) If you continue to experience problems, contact your local Sealey service agent.
5.4 For a full service contact your local Sealey service agent.
5.5 When not in use, disconnect from air supply, clean and store in a safe, dry, childproof location.
Environmental Protection.
Recycle unwanted materials instead of disposing of them as waste.
All tools, accessories and packaging should be sorted, taken to a recycle centre
and disposed of in a manner which is compatible with the environment.
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [email protected] or telephone 01284 757500.
MAT150AS, MAT150SC, MAT110AS Issue No 2 (SP) 21/08/13 Original Language Version © Jack Sealey Limited 2013
MAT150SC
MAT150AS
MAT110AS