Sealey GSA08 - Manual (Page 2)

2. INTRODUCTION & SPECIFICATION
3.1. Air Supply
3.1.1. Ensure the sander air valve (or throttle) is in the "off" position before connecting to the air supply.
3.1.2. You will require an air pressure between 70-90psi, and an air flow according to the specification above.
3.1.3. p WARNING! Ensure the air supply is clean and does not exceed 90psi while operating the sander.
Too high an air pressure and unclean air will shorten the product life due to excessive wear, and may be
dangerous causing damage and/or personal injury.
3.1.4. Drain the air tank daily. Water in the air line will damage the sander and will invalidate your warranty.
3.1.5. Clean air inlet filter weekly. Recommended hook-up procedure is shown in fig.1.
3.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres).
The minimum hose diameter should be 1/4” I.D. and fittings must have the same inside dimensions.
3.1.7. Keep hose away from heat, oil and sharp edges. Check hoses for wear, and make certain that all
connections are secure.
3.2. Couplings.
Vibration may cause failure if a quick change coupling is connected directly to the air sander. To overcome
this, connect a leader hose to the sander. A quick change coupling may then be used to connect the
leader hose to the air line recoil hose (See fig.1 & fig.2).
3.3. Dust Collection (GSA09 only).
The dust outlet tube of the sander must be connected to a dust-free system in accordance with COSHH
and any other regulations that may apply to the work area. For information on dust-free systems, contact
your local Sealey dealer.
3. PREPARING SANDER FOR USE
LEAD PAINT WARNING!
Paint once contained lead as a traditional ingredient. Contact with the dust from the removal of such paint
is toxic and must therefore be avoided. The following action must be taken before using the sander
on a surface that you suspect may contain lead paint.
1. User must determine potential hazard relating to age of paint to be removed.
(Modern paints do not have lead content).
2. DANGER! Keep all persons and pets away from the working area. The following persons are
particularly vulnerable to the effects of lead paint dust: Expectant women, babies and children.
3. We recommend personal protection by using the following safety items:
a) Paint Spray Respirator (Sealey Part No. SSP1604)
b) PE Coated Hooded Coverall (Sealey Part No. SSP267).
c) Latex Gloves (Sealey Part No. SSP24).
4. Take adequate measures to contain the paint dust, flakes and scrapings.
5. Continue to wear safety equipment as in (3) above and thoroughly clean all areas when task is
complete. Ensure paint waste is disposed of in sealed bags or containers.
fig.1
Pad size Ø:. . . . . . . . . . . . . . . . . . . . . 150mm
Thread size: . . . . . . . . . . . . . . . . . .5/16” UNF
Free Speed: . . . . . . . . . . . . . . . . . . 10000rpm
Orbit Size Ø:. . . . . . . . . . . . . . . . . . . . . . 5mm
Operating Pressure: . . . . . . . . . . . . . . .90psi
Air Consumption: . . . . . . . . . . . . . . . . . 5cfm
Air Inlet: . . . . . . . . . . . . . . . . . . . . . 1/4”BSP
Noise Power: . . . . . . . . . . . . . . . . .97.64dB.A
Noise Pressure: . . . . . . . . . . . . . . .86.64dB.A
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . .0.8kg
Generation Series Air Palm Orbital Sander features composite housing for reduced chill and vibration. Variable
speed control lever for quick adjustment to suit workpiece. Fitted with dual bearings in eccentric assembly to
maximise working life. Exhaust muffler helps reduce noise emission. (GSA09 only - dust-free outlet for use with
centralised dust extraction systems). Supplied with hook-and-loop pad.
fig.2
Original Language Version
GSA08,GSA09 Issue: 2 - 13/07/13 © Jack Sealey Limited