Sealey SA355 - Manual (Page 3)

4.1. Unpack the product and check contents
against the parts listed below. If there is
anything damaged or missing contact your
supplier immediately.
Contents:
a) SA355 Belt Sander.
b) Spare sanding Belt
c) 1 x Hex. Key

WARNING! Ensure that you have read, understood and apply Section 1 safety instructions.
4.2. Refering to fig. 3, loosen the clamp bolt (1) to allow the angle between the grip and the belt to be altered
to suit the job in hand. After adjustment retighten the clamp bolt.
4.3. Once connected to the air supply the sander is started by pushing the lock and squeezing the trigger (2).
4.4. To remove and replace the sanding belt push the nose roller (3) towards the drive pulley (4) against
spring pressure. The nose roller bracket (5) will retract and lock allowing removal/fitting of the belt. When
the new belt is in position release the pulley bracket by pushing in and holding the nose roller bracket (5),
then press and hold the tension bar (6) whilst releasing the pressure on the nose roller bracket.
4.5. The tracking of the belt can be altered by adjusting the two recessed
hex socket screws on the nose roller bracket (see fig.4). Turning the
screw ‘A’ in either direction will alter the lateral position of the the nose
roller within its bracket. Turning the screw ‘B’ in either direction will alter
the lateral position of the complete nose roller bracket in relation to the
body of the sander.
4.6. To adjust the track of the belt, disconnect the sander from the air supply
and remove the belt as described in paragraph 4.4. Loosen the lock nut
holding screw ‘B’ in position so that screw ‘B’ can be easily adjusted using the hex key provided. Replace
the belt, reconnect the air supply and operate the sander, observing the track of the belt. Adjust the track
of the belt by turning the screws ‘A’ and ‘B’ until the belt is running true. When the belt is running true,
switch off, disconnect from the air supply and remove the belt. Secure screw ‘B’ into position with the lock
nut and replace the belt.
 WARNING! Disconnect sander from air supply before changing accessories, servicing or performing
maintenance. Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
5.1. If the air supply system does not have an oiler, lubricate the sander daily with a few drops of a good
grade air tool oil, such as Sealey ATO500S, dripped into the air inlet (fig.3.7) before use.
5.2. Clean the sander after use and change belt when required.
5.3. Loss of power or erratic action may be due to the following:
a) Excessive drain on the air supply. Moisture or restriction in the air line. Incorrect size or type of hose
connectors. To remedy, check the air supply and follow instructions in Section 3.
b) Grit or gum deposits in the sander may also reduce performance. If your model has an air filter
(located in the area of the air inlet), remove the filter and clean it. Flush the sander out with gum
solvent oil or an equal mixture of SAE No.10 oil and kerosene. Allow to dry before use.
If you continue to experience problems, contact your local Sealey service agent.
5.4. For a full service contact your local Sealey service agent.
5.5. When not in use, disconnect from air supply, clean and store in a safe, dry, childproof location.
4. OPERATING INSTRUCTIONS
5. MAINTENANCE
fig.3
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534 [email protected]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park ,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
Original Language Version
©Jack Sealey Limited 2013 SA355.V2 Issue: 2 (SP) - 22/08/13
Environmental Protection.
Recycle unwanted materials instead of disposing of them as waste.
All tools, accessories and packaging should be sorted, taken to a recycle centre
and disposed of in a manner which is compatible with the environment.