Sealey SA18/S - Manual (Page 3)


WARNING! Disconnect sander from air supply before changing accessories, servicing or performing
maintenance. Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
5.1. If the air supply does not have an oiler, lubricate the air sander daily with a few drops of good grade air
tool oil such as Sealey ATO/500 or ATO1000, dripped into the air inlet before use.
5.2. Clean the sander after use and change pads when required.
5.3. Loss of power or erratic action may be due to the following:
a) Excessive drain on the air line. Moisture or restriction in the air pipe. Incorrect size or type of hose
connectors. To remedy check the air supply and follow instructions in chapter 3.
b) Grit or gum deposits in the sander may also reduce performance. If your model has an air strainer
(located in the area of the air inlet), remove the strainer and clean it. Flush the sander out with gum
solvent oil or an equal mixture of SAE No 10 oil and kerosene. Allow to dry before use.
If you continue to experience problems, contact your local Sealey service agent.
5.4. For a full service contact your local Sealey service agent.
5.5. When not in use, disconnect from air supply, clean sander and store in a safe, dry, childproof location.
4. OPERATING INSTRUCTIONS
5. MAINTENANCE

WARNING! Ensure you read, understand and apply safety instructions before use.
4.1. Assembly
4.1.1. Your SA18/S comes with one handle, two spanners, and a backing disc.
4.1.2. The handle may be screwed into the left- or right-hand side of the head.
4.1.3. Apply appropriate sanding pad to the backing disc. Use only pads with speed ratings equal to,
or higher than, the speed rating of the sander. DO NOT use cloth backed sanding pads.
4.1.4. Remove the disc locking nut from the sander hub. Screw the backing disc onto the central spindle and
secure with the locking nut. Use spanners supplied to hold the hub and tighten the lock nut.
4.1.5. Connect air supply to sander and press the control valve lever to check that the sander is working correctly.
4.2. Operating
The air flow may be regulated by turning the control valve screw on top of the handle.
Always use grit pad appropriate for the job. Work progressively from coarse grades to finer grades.
DO NOT go from coarse to fine in one step as it may be difficult to remove swirl marks left by the coarser
grit.
DO NOT apply excessive pressure, let the sander do the work for you. Start the sander and bring the
sanding disc to the the work surface evenly and slowly. Move the sander back and forth in overlapping
areas. Remove the sanding disc from the work surface before stopping the sander. Regularly check the
sanding pad for wear, always change a cracked or damaged pad.
DO NOT allow sander to run in “idle rotation” for an extended period of time as this will shorten life of
bearings.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534 [email protected]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park ,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
Environmental Protection.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and
packaging should be sorted, taken to a recycling centre and disposed of in a manner which is
compatible with the environment.
© Jack Sealey Limited Original Language Version SA18/S.V2 Issue:3(SP) - 17/10/13