Sealey SA792 User Manual
Air nail/staple gun 50, Capacity, Sa792.v3
InstructIons For:
AIR NAIL/STAPLE GUN 50
mm
/ 40
mm
CAPACITY
model no:
SA792.V3
1. SAfETY
3. SPECIfICATIoN
2. INTRodUCTIoN
sA792.V3 Issue: 1 - 12/05/14
Original Language Version
© Jack sealey limited
IMPORTANT: PLEASE REAd THESE INSTRUCTIoNS CAREfULLY. NoTE THE SAfE oPERATIoNAL REQUIREmENTS, WARNINGS & CAUTIoNS. USE THE
PRodUCT CoRRECTLY ANd WITH CARE foR THE PURPoSE foR WHICH IT IS INTENdEd. fAILURE To do So mAY CAUSE dAmAGE ANd/oR
PERSoNAL INJURY ANd WILL INVALIdATE THE WARRANTY. KEEP THESE INSTRUCTIoNS SAfE foR fUTURE USE.
Thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
WARNING! do NoT use the nail/staple gun if damaged, has missing parts or is thought to be faulty. contact your service Agent.
WARNING! disconnect from the air supply before loading or servicing.
WARNING! Always wear approved eye, face and hand protection when operating the nail/staple gun.
WARNING! check correct air pressure is maintained and not exceeded. We recommend 70 to 110psi.
do NoT use the nail/staple gun for a task it is not designed to perform.
do NoT operate the nail/staple gun near flammable substances or flammable containers.
do NoT use the nail/staple gun unless you have been instructed in its use by a qualified person.
do NoT carry the nail/staple gun by the air hose, or yank the hose from the air supply.
do NoT operate the nail/staple gun if you are tired or under the influence of alcohol, drugs or intoxicating medication.
do NoT carry the nail/staple gun with your hand on the power trigger in order to avoid unintentional firing.
do NoT direct the nail/staple gun or the air from the air hose at yourself or others.
do NoT load bent or damaged nails/staples into the magazine.
▲
dANGER! When putting the nail/staple gun down, ensure that the trigger safety slide is not fouled, risking accidental firing.
maintain the
nail/staple gun in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised
parts may be dangerous and will invalidate the warranty.
Keep the air hose away from heat, oil and sharp edges. check the air hose for wear before each use and ensure that all
connections are secure.
only use supplied 18sWG x 10-50mm Brad nails and 18sWG x 13-40mm staples. Ask your sealey dealer for further supplies.
Wear approved safety eye/face shield, ear defenders and hand protection.
Follow all workshop safety rules, regulations, and conditions when using the nail/staple gun.
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
Keep children and non essential persons away from the working area.
When not in use, disconnect from the air supply, remove the strip nails/staples from the magazine and store cased in a safe, dry,
childproof location.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into
this product, but must be applied by the operator.
Professional air nailer/stapler with lightweight aluminium body and rubber grip handle. Features 2-stage operation trigger to fire single or
multiple staples/nails. safety trigger device to prevent accidental firing of nails and staples. supplied in carry-case with oiler and starter pack of
nails and staples.
model No: . . . . . . . . . . . . . . . . . SA792.V3
nail capacity:. . . . . . . . .10-50mm 18sWG
staple capacity: . . . . . . .13-40mm 18sWG
maximum Pressure:.. . . . . . . . . . 70-110psi
Air Inlet size:. . . . . . . . . . . . . . . . . 1/4"BsP
Gun Weight: . . . . . . . . . . . . . . . . . . .1.35kg
noise Power: . . . . . . . . . . . . . . . 98.5dB(A)
noise Pressure: . . . . . . . . . . . . . 85.5dB(A)
Vibration: . . . . . . . . . . . . . . . . . . . . 2.5m/s²
uncertainty: . . . . . . . . . . . . . . . . . 1.25m/s²
spring loaded
safety slide
magazine
latch
fig.1
1.05 x 1.26mm
2mm x 1.26mm
10-50mm
Fastener type (Brad)
5.7mm
1.05 x 1.26mm
13-40mm
Fastener type (staple)
Inoperable
position
Firing
position
thumb
wheel