Sealey SA43 - Manual (Page 2)

2. INTRODUCTION / SPECIFICATION
3.1 AIR SUPPLY
Recommended hook-up is shown in fig 1.
 WARNING! Ensure the air supply is clean and does not exceed 90psi while operating the grinder.
Too high an air pressure and/or unclean air will cause excessive wear, and may be dangerous, causing
damage and/or personal injury.
3.1.1 Ensure that the grinder air valve (or throttle) is in the "off" position before connecting to the air supply.
3.1.2 You will require an air pressure between 70-90psi, and an air flow according to the specification above.
3.1.3 Drain the air tank daily. Water in the air line will damage the grinder and invalidate your warranty.
3.1.4 Clean air inlet filter weekly.
3.1.5 Line pressure should be increased to compensate for unusually long air hoses (over 8 metres).
The minimum hose diameter should be 1/4” I.D. and fittings must have the same inside dimensions.
3.1.6 Keep hose away from heat, oil and sharp edges. Check hoses for wear, and make certain that all
connections are secure.
3.2 COUPLINGS
3.2.1 Vibration may cause failure if a quick change coupling is connected directly to the grinder. To prevent this,
connect a leader hose - Sealey model number AH2R or AH2R/38 - to the grinder. A quick change
coupling may then be used to connect the leader hose to the air line recoil hose. See figs. 1 & 2 on next
page.
3. PREPARING GRINDER FOR USE
1.2. LEAD PAINT WARNING!
Paint once contained lead as a traditional ingredient. Contact with the dust from the removal of such
paint is toxic and must therefore be avoided. The following action must be taken before using the
grinder on a surface that you suspect may contain lead paint.
1. User must determine potential hazard relating to age of paint to be removed (modern paints do
not have lead content).
2. DANGER! Keep all people and pets away from the working area. The following are particularly
vulnerable to the effects of lead paint dust: Pregnant women, babies and children.
3. We recommend personal protection by using the following safety items:
a) Paint Spray Respirator (Our ref SSP1699)
b) PE Coated Hooded Coverall (Our ref SSP266). c) Latex Gloves (Our ref SSP24).
4. Take adequate measures to contain the paint dust, flakes and scrapings.
5. Continue to wear safety equipment as in (3) above and thoroughly clean all areas when work is
complete. Ensure that paint waste is disposed of in sealed bags or containers according to local
regulations.
fig. 1
Disc Diameter: . . . . . . . . . . . . . . . . . . 100mm
Free Speed: . . . . . . . . . . . . . . . . . . 11000rpm
Operating Pressure: . . . . . . . . . . . . . . .90psi
Air Consumption: . . . . . . . . . . . . . . . . . . 4cfm
Air Inlet: . . . . . . . . . . . . . . . . . . . . . . 1/4”BSP
Noise Power: . . . . . . . . . . . . . . . . . . 86dB(A)
Noise Pressure: . . . . . . . . . . . . . . . . 82dB(A)
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . .1.5kg
Grinding Disc Part No.: . . . . . . . . PTC/100G
Backing Disc Part No.: . . . . . . . . . . PTC/BP3
Aluminium body and bevel gear housing with steel disc guard. Well-balanced, multi-purpose tool suitable for
general workshop use. Supplied with grinding disc, locking and pin spanners.
fig. 2
Original Language Version
DO NOT USE
QUICK FIT
COUPLING AT THIS POINT
© Jack Sealey Limited 2013 SA43.V3 Issue: 3 (SP) - 02/09/13