Sealey SA120 - Manual (Page 2)

Ensure you have read understood and follow the safety instructions in Section 1.
4.1. Attach the retaining spring by holding the front end of the spring and screwing it onto the gun retainer.
4.2. Insert the chisel using the spring’s hooked end to hold the chisel in place.
4.3. Attached the tool to the air supply as mentioned in Section 2.
4.4. To operate the hammer, squeeze the trigger.
NOTE: The air regulator may be used as a means of throttle control.
Chisel: Available from your authorised Sealey Dealer. Part No: SA120/P - Pointed SA120/F - Flat.
 WARNING! Disconnect the hammer from the air supply before changing accessories, servicing or performing any maintenance.
5.1 Keep the hammer oiled for optimum performance
lubricate daily with a good grade of air oil such as Sealey ATO/500 or ATO/1000. If no air tool oiler is used, a teaspoon of oil can be
poured into the tool’s air inlet, or into the hose at the nearest connection to the air supply. Then run the hammer for a short time.
5.2. When not in use, always turn off air supply.
Note: The following external factors may cause loss of power and effect hammer performance:
The air system.
Reduced compressor output, excessive drain on the air line, moisture or restrictions in air pipes or in the use of hose connection
having the improper size. Correct the condition accordingly.
The Tool
Grit or gum deposits in the tool. Correct by cleaning the air stainer,if present, and flushing out the tool with gum solvent oil or an equal
mixture of
SAE No.10 oil and kerosene.
If despite taking action as for above situations the tool function is impaired, contact your local Sealey service dealer for advice.
4. OPeRATING INsTRUCTIONs
5. mAINTeNANCe
Risk of hand Arm Vibration Injury.
The SA120.V2 Air Hammer, when operated in accordance with these instructions and tested in accordance with EN 28662-2: 1994, results in
the following vibration emission declared in accordance with BS EN12096: 1996.
Measured vibration emission value: . . . . . . . . . 6.6m/s² Uncertainty: . . . . . . . . . . . . . . . . . 2.64m/s²
These values are suitable for comparison with emission levels of other tools that have been subject to the same test.
This tool may cause hand-arm vibration syndrome if its use is inadequately managed.
Recommended measures to reduce risk of hand-arm vibration syndrome:
This item represents a low Hand Arm Vibration risk to users. The calculated minimum usage period exceeds 8 hours. We recommend appropriate
safety equipment is utilised and regular breaks for the operator are employed to reduce any residual risk of fatigue or repetitive strain injury.
The air hammer is designed primarily for use on vehicle bodywork. We do not recommend any other use. Contact your supplier immediately
should there be any missing, or damaged parts. Chisels not included.
3. INTRODUCTION & sPeCIFICATIONs
Chisel Shank Size . . . . . . 12.7 x 47mm
Speed . . . . . . . . . . . . . . . . . . . 3000bpm
Air Consumption. . . . . . . . . . . . . . 4cfm
Operating Pressure . . . . . . . . . . . 90psi
Air Inlet Size . . . . . . . . . . . . . . .1/4”BSP
Piston Stroke . . . . . . . . . . . . . . . 20mm
Vibration level . . . . . . . . . . . . . 6.6m/s²
Sound Pressure level . . . . . . . .96.5dB
Sound Power level . . . . . . . . .107.7dB
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
ImPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORmATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534 [email protected]
sole UK Distributor, sealey Group,
Kempson Way, Suffolk Business Park ,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
Original Language Version SA120.V2 Issue: 2 - 04/11/09