Specifications – JBL Synthesis SDP-25 User Manual
Page 19
-
19
-
SPECIFICATIONS
MAIN ZONE AUDIO
Frequency Response:
20 Hz – 20 kHz, ±0.25dB
Analog Input Impedance:
47K ohms
Input Level:
4 Vrms in DSP modes
4 Vrms in 2Ch Bypass Mode
Output Impedance:
480 Ohms
Digital Coax Signal Strength:
0.5V p-p
Output Level:
4 Vrms
Signal-to-Noise Ratio:
90dB in DSP Modes
98dB in 2ch Bypass Mode
THD + Noise:
<0.007% in DSP Modes
<0.015% Analog in - Bypass & DSP Modes
1 kHz at 1.0VRMS
Bass Management:
High-Pass Filter:
Low-Pass Filter:
2nd order (x7)
4th Order, 40 - 200Hz Crossover Freq.
Audio Resolution:
Up to 7.1 Channels at 192kHZ/24-bit
Supported Audio Formats:
Dolby TrueHD, DTS-HD Master Audio, DVD Audio
Crosstalk:
<72dB
A/D Conversion:
24-Bits, up to 192 KHz, Delta-Sigma
114dB DR, -100dB THD+N
D/A Conversion:
24-Bits, up to 192 KHz, Delta-Sigma
114dB DR, -100dB THD+N
DSP Engine:
Dual TI TMS320D
Low Frequency Cutoff:
< 10Hz (All speaker channels in Bypass Mode)
High Frequency Cutoff:
>200Hz (All speakers in Bypass mode, -3dB point)
VIDEO INPUT & OUTPUT CONNECTIONS:
HDMI Inputs:
6 HDMI Type A (19 pin) connectors
HDMI Outputs:
1x HDMI Type A (19 pin) connection with
Audio Return Channel
1x HDMI Type A (19 pin) connection for Main/2nd Zone
HDMI Features:
12-bit Deep Color (1080p)
3D Pass-through
xvYCC (x.v. Color)
Video bandwidth up to 300 MHz
4K support to 2160, 50p/60p, 8-bit, 4:2:0
Composite (CVBS) Video Inputs:
2x @ 1.0V p-p, 75 ohms
Composite (CVBS) Video Outputs:
1x 1.0Vp-p, 75 ohms
Component Video Inputs:
Cb/Cr, Pb/Pr:
Y:
2x
0.75Vp-p, 75 ohms
1V p-p, 75 ohms
AUDIO INPUT & OUTPUT CONNECTIONS:
Analog Audio Inputs:
5x stereo single-ended/unbalanced L/R pairs
1 set 7.1 single-ended/unbalanced (L/C/R/LS/RS/LBS/
RBS/Sub)
1x 3.5mm stereo (Front Panel)
Analog Audio Outputs:
2x stereo single-ended/unbalanced L/R pairs
1 set 7.2 single-ended/unbalanced (L/C/R/LS/RS/LBS/
RBS/Sub 1/Sub2)
Digital Audio Inputs:
6x via HDMI
5x Coaxial (RCA) 75 ohms (S/P-DIF)
5x Optical Toslink (S/P-DIF)
1x USB 2.0 Type B
DATA AND CONTROL CONNECTIONS:
Trigger Outputs:
2x 12 VDC, 300mA, Trigger B programmable
USB:
1x USB Type A for software updates only
Data Connection:
RS-232 via DB-9 connector for Control and System
Feedback
IR Inputs:
Front Panel IR sensor, switch selectable for on/off
1x IR in, 1x Flasher In, 3.5mm jacks
IR Outputs:
3x, 3.5mm jacks
ELECTRICAL & PHYSICAL SPECIFICATIONS:
Mains Voltage:
120 VAC or 230 VAC [factory-set]
Power Consumption:
Standby: < 0.5 watts
Maximum Power: 20 watts
Unit Dimensions [H x W x D]
6" x 19" x 16.3" / 153 x 483 x 414 mm
Shipping Dimensions: [H x W x D]
11.4x 20.6" x 24.2" / 288mm x 522mm x 613mm
Unit Weight:
19.5 lb/8.86 kg
Shipping Weight:
26.5 lb/12 kg
Specifications