Invotel SX8600 - Manual

• Insert the Flash card into the blue connector in the front of unit.
• Plug AC adapter (110V AC to 12V AC), the Green LED on the back turns ON.
• Confirm that all 4 Red LED lights in front of this unit are double BLINKING
• Use one of your telephones and unplug the cord for L1/L2 from it and connect it
to 1/2/3 PHONE LINES jack on SX8600 (the 1
st jack from 12VAC), now connect
1/2/3 TELEPHONE jack on SX8600 (3 rd jack) to your telephone using the
provided phone cord, make sure you have dial tone on your lines 1 and 2
• Now unplug the cord for L3/L4 from your phone and connect it to 3/4 PHONE
LINES jack on SX8600 (the 2nd jack from 12VAC) and connect 3/4
TELEPHONE jack on SX8600 (4
th jack) to your telephone using the provided
phone cord, make sure you have dial tone on your lines 3 and 4
• Observe that as you connect the lines the blinking lights turn OFF. (on non
existing lines the lights keep blinking and that is OK)
• • • • Alternatively you may use a splitter (T adapter) at the Wall jack to connect both
this device and a telephone (in that case the 3
rd and 4 th jacks are not connected)
• Set the volume to mid level.
L3/L4 L1/L2/L3 L3/L4 L1/L2/L3 12VAC
TELEPHONE PHONE LINES 600ma
WALL
JACK PHONE
WALL
JACK PHONE
110 V
AUDIO
TEST
Problems Possible Cause / Solution
P16
Innovative Telecommunication Technology LLC.
1112 Montana Ave Suite 250 Santa Monica, CA 90403 USA
Tel: 310-899-0078 Fax: 310-857-6401 http://www.invotel.com
10. Hold Music activates in
a conference call or
when two phones pick
up at same time • If for any reason the hold music is activated
inadvertently, it can always be deactivated by pressing
the FLASH button in any setting.
• Conference calls can be done a better way: Press
FLASH, you will get a dial-tone now dial the phone
number of the 2
nd party then press FLASH to join the
two calls together.
L1 L2 L3 L4
3/4 1/2
6. MOH works but audio
does not stop when call
is picked up in 1 or 3
settings. • Wire distance to adapter is too long, Centralize the
location of device to be as close as possible to all the
phones. Try the 2 setting for maximum power.
• If you are re-wiring “daisy chain” wiring works better than
” star” or “home run” or Independent wiring
• Press FLASH button to stop the music.
7. Some Phones work ,
some do not • All your phones need to be same model for activation
in 1 or 2 settings. If you mix different phone models,
Use the 3 setting (refer to pages 3 or 4 for more
details)
8. Randomly Hold music
starts to play by it self
or does not activate in
1, 2 or 3 settings • The call needs to be on Hold min. 2 sec. before you
may pick it up.
• When you hang up, wait 2 seconds before selecting
the same line again.
• Check for extra devices sharing that line like Message
indicator, Answering machine, Alarm system, Modem
etc. Use a “privacy module” between the line and that
extra device to keep them off the line when line is
being used by your phone.
• Set your Alarm system and/or your DSL line to share
FAX line.
• Excessive wiring- Total wire length per line must be
under 500 feet ( Ex: if you have 9 wall jacks -no matter
spare or a phone plugged in- each connected via a
100 foot wire to a common point then your total wire
length is 9 x 100=900 feet )
• Use FLASH button to deactivate music.
9. Audio shuts off or
flickers • Extensive audio volume. Lower the volume to proper
level.
Microphone IN
A B C 1 2 3
VOLUME
STATUS 1 2
REC
BANK
SWITCH
Flash Card
If you have PBX or KSU type phone system connect just the WALL
JACKs to input side of your PBX lines in parallel.
If you have regular phones, only one telephone is optionally
connected to this device, other telephones remain connected to
their own wall jacks.
Model # SX8600 Rev 25.8
All-In-One Auto Attendant + Greeting +
Music-On-Hold Player/Recorder/Adapter
Audio IN for recording
Ring OUT in B setting Audio OUT to headset (Flash card in place)
Live Audio Input for On Hold (if Flash card removed)