Invotel SX1025 - Manual

Music-On-Hold Adapter Installation
AudioImage
™
Model # SX1025
Rev 22T
• Connect “WALL jack” to your “Wall” Jacks using the provided cord .
• • • • This device monitors all the telephones through the lines. You may use a splitter
(T adapter) at the Wall jack to connect both this device and a telephone. If you
do not have a splitter use the “PHONE” jack on this device to plug the
telephone.
Please note that just one phone may be optionally connected to this
device, other telephones remain connected to their own wall jacks.
Plug the Audio cable into Audio IN jack on the AudioImage™ Music On Hold
controller, Plug the other end of audio cable into the “Headphone” jack of your
audio source such as digital player (8 ohm or 600 ohm), Radio, CD Player, PC
CD ROM headphone, PC sound card, speakers output etc.
We recommend you to set the volume on your audio source to mid level
Note: extensive volume can shut off the on-hold audio.
(please note some music titles are not royalty-free and you may want to use the royalty-
free music titles to avoid annual licensing payments to ASCAP and BMI for playing those
titles on-hold)
RCA L1 &2 L1 & 2
Audio IN OUT IN
Wall
jack
Phone
ALT1 ALT2
L2 L1
• Unplug the phone lines; Wait 60 seconds then Plug them back IN.
make sure the phone line is plugged in securely.
• Select Line 1 on the phone & make sure that there is dial tone.
2. No Audio
• check audio cord; try inserting it half way, adjust the volume on your
audio source if needed to hear it.
3. Audio source is OK but no
audio when device is
activated as per ALT1 or
ALT2 setting.
• Verify that the audio source is playing by itself, listen to it. Use the
Headphone jack on a CD player not the “line out”
• Set Volume to Medium.
• If answering a call allow a second before placing the call on HOLD.
• Check to see if L1 or L2 lights on this device has turned ON
• model SX1025 does not activate by pressing Hold button
• you need to press Flash button 1
st then Hold button. On some
phones wait a second after pressing Flash then press Hold.
4. MOH works but audio does
not stop when call is picked
up in any setting • Press FLASH button to stop the audio
• Wire distance to adapter may be too long(more than 200 feet),
Centralize the location of device to be as close as possible to the
phones.
5. Some Phones work , some
do not in ALT1 setting • Try changing the setting to ALT2 setting and follow the Operation in
ALT2 settings.
6. Some times audio starts to
play by it self or does not
deactivate
by voice
• Press FLASH button to stop it.
• The call needs to be on Hold at least 4 seconds before it can be
voice deactivated, use Flash to deactivate.
• When you hang up, wait 2 seconds before selecting the same line.
• Check for other devices sharing that line like Message indicator,
Answering machine, Alarm system, Modem etc. Use a privacy
module between the line and that device to keep them off the line
when line is being used by your phone.
• Set your Alarm system and/or your DSL line to share FAX line.
• Excessive wiring- Total wire length per line must be under 200 feet.
• Try putting the call back on Hold, wait 3-4 seconds then pick up.
1. Adapter not working or
stopped working
Problems Possible Cause / Solution
7. Audio shuts off or flickers • Extensive audio volume, adjust the volume to proper level.
P4
Innovative Telecommunication Technology
1112 Montana Ave Suite 250 Santa Monica, CA 90403 USA
Toll-Free: 800-747-0708 Tel: 310-899-0078 Fax: 310-899-0227 http://www.invotel.com ®