Verilink PRISM 3000 (34-00184) Product Manual - Manual (Page 42)

PRISM 3000 4-14 Terminal Operation
SNMP traps. When a network alarm occurs, the unit sends a
trap message to up to 6 destinations on the user’s network.
The trap message is formatted per RFC 1157. The generic
trap type is ‘enterpriseSpecific’ (generic-trap = 6).
When an alarm group is defined to report via SNMP, up to 6
Trap IP addresses can be assigned. The PRISM will report
each alarm by transmitting an SNMP ‘Trap’ to each Trap IP
address. T1 network problems often cause more than one
alarm type. In these cases, multiple trap messages are gener-
ated, each with a different specific trap type. The specific-
trap field of each trap message is set to one of the values
shown in the ‘Trap Definition’ table on the previous page.
The following five menu items require the entry of up to 255
characters identifying the appropriate group, person, device
function, or unit location.
Read Community: This display accepts a character string
identifying the group authorized to perform read operations.
The default setting is ‘
public ’.
Write Community: This display accepts a character string
identifying the group authorized to perform write opera-
tions. The default setting is ‘
private ’.
System Contact: This display accepts a character string
identifying the person responsible for a network device. The
default setting is ‘
no system contact ’.
System Name: This display accepts a character string iden-
tifying the functionality of the network device. The default
setting is ‘
no system name ’.
System Location: This display accepts a character string
identifying the physical location of network device. The
default setting is ‘
no system location ’.
3000 DSU x.xx/x.xx PRISM 3000 Date: MM/DD/YY
No Far End Response Boston: (232) Time: HH:MM:SS
--------------------------- Voice Port Configuration ---------------------------
Element: (NEAR)
Slot: (3)
Card Type: 4 Wire E&M
Port DS0 Mode State Name/ID Sig. Tx Gn. Rx Gn.
-------------------------------------------------------------------------------
A (13) [ACTIVE] BUSY (DS0 13 ) [FXS/LS] [ 0dB] [ -6dB]
B (14) [ACTIVE] BUSY (DS0 14 ) [FXS/GS] [ 0dB] [ -6dB]
C (15) [ACTIVE] BUSY ( ) [MEG/LS] [ 0dB] [ -6dB]
D (16) [ACTIVE] BUSY ( ) [MEG/GS] [ 0dB] [ -6dB]
E (17) [ACTIVE] BUSY ( ) [PLAR ] [ 0dB] [ -6dB]
F (18) [SPARE ] IDLE ( ) [FXS/LS] [ 0dB] [ -6dB]
Channel Allocation: 1x1x1x 1x1x1x -
----- ------
Firmware Revision: x.xx
Screen 4-11 Voice Parameters
Trap Definitions
Cleared
Near
Cleared
Far
Alarmed
Near
Alarmed
Far
Description
4 54 104 154 DTE CRCES
5 55 105 155 DTE BPVS
6 56 106 156 DTE AISS
7 57 107 157 DTE RAS
8 58 108 158 DTE UAS
9 59 109 159 DTE OOFS
10 60 110 160 DTE LOSS
11 61 111 161 DTE CSS
12 62 112 162 DTE SES
13 63 113 163 DTE ES
14 64 114 164 NET CRCES
15 65 115 165 NET BPVS
16 66 116 166 NET AISS
17 67 117 167 NET RAS
18 68 118 168 NET UAS
19 69 119 169 NET OOFS
20 70 120 170 NET LOSS
21 71 121 171 NET CSS
22 72 122 172 NET SES
23 73 123 173 NET ES
24 74 124 174 Device Reset