Verilink M1-3 (880-503136-001) Product Manual - Manual (Page 32)

M1-3 Configuration Options
3-2 Verilink M1-3 User Manual
Terminal Access To access the M1-3 from an ASCII terminal:
1. Connect the ASCII terminal to the SCM front panel L OCAL port.
2. Set the ASCII terminal parameters to the following values:
• 19.2 kbit/s
• 8 data bits
• no parity
• one stop-bit
• no flow control
NOTE: Ensure that X- ON /X- OFF flow control is disabled.
3. Type “craft” and press E NTER .
4. At the password prompt, type the password systest (lower
case) and press E NTER .
The SCM Main Menu displays ( Figure 3-1 ).
Figure 3-1 SCM/M1-3 Main Menu
-- VERILINK SCM CONTROLLER : FW Rev 1.17, Aug 18 1998 15:36:44 -- -- VERILINK SCM CONTROLLER : FW Rev 1.17, Aug 18 1998 15:36:44 -- -- VERILINK SCM CONTROLLER : FW Rev 1.17, Aug 18 1998 15:36:44 -- -- VERILINK SCM CONTROLLER : FW Rev 1.17, Aug 18 1998 15:36:44 --
Site name: SCM Tutorial Access level: 4 Site name: SCM Tutorial Access level: 4 Site name: SCM Tutorial Access level: 4 Site name: SCM Tutorial Access level: 4
Managing at NEAR end node [0.0.0.2] Node id: 122
Managing at NEAR end node [0.0.0.2] Node id: 122 Managing at NEAR end node [0.0.0.2] Node id: 122 Managing at NEAR end node [0.0.0.2] Node id: 122
<- SLOT -> <- SLOT -> <- SLOT -> <- SLOT ->
SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13
SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13 SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13 SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13
0 - - - - - - - - - - - - -
0 - - - - - - - - - - - - - 0 - - - - - - - - - - - - - 0 - - - - - - - - - - - - -
1 M *S D Q Q I [M] - - - - - - -
1 M *S D Q Q I [M] - - - - - - - 1 M *S D Q Q I [M] - - - - - - - 1 M *S D Q Q I [M] - - - - - - -
2 - - - - - - - - - - - - -
2 - - - - - - - - - - - - - 2 - - - - - - - - - - - - - 2 - - - - - - - - - - - - -
3 - - - - - - - - - - - - -
3 - - - - - - - - - - - - - 3 - - - - - - - - - - - - - 3 - - - - - - - - - - - - -
4 - - - - - - - - - - - - -
4 - - - - - - - - - - - - - 4 - - - - - - - - - - - - - 4 - - - - - - - - - - - - -
KEY: D=QUAD D, I=IMUX, M=M1-3, Q=QUAD T1, S=SCM
KEY: D=QUAD D, I=IMUX, M=M1-3, Q=QUAD T1, S=SCM KEY: D=QUAD D, I=IMUX, M=M1-3, Q=QUAD T1, S=SCM KEY: D=QUAD D, I=IMUX, M=M1-3, Q=QUAD T1, S=SCM
S) shelf/slot O) administration S) shelf/slot O) administration S) shelf/slot O) administration S) shelf/slot O) administration
C) configuration D) diagnostics
C) configuration D) diagnostics C) configuration D) diagnostics C) configuration D) diagnostics
P) performance/status F) display far end DS3 port identification
P) performance/status F) display far end DS3 port identification P) performance/status F) display far end DS3 port identification P) performance/status F) display far end DS3 port identification
B) circuit manager A) alarm
B) circuit manager A) alarm B) circuit manager A) alarm B) circuit manager A) alarm
R) remote end setup I) manufacturing info
R) remote end setup I) manufacturing info R) remote end setup I) manufacturing info R) remote end setup I) manufacturing info
X) logoff
X) logoff X) logoff X) logoff
A [0.0.0.2] [1,6] M1-3 > A [0.0.0.2] [1,6] M1-3 > A [0.0.0.2] [1,6] M1-3 > A [0.0.0.2] [1,6] M1-3 >